Results 91 to 100 of about 7,332 (264)

Scalable and Multifunctional PAN‐MXene Composite Fibers for Thermal Management, Photothermal Conversion, Energy Harvesting, and Sensing for Wearable Applications

Advanced Materials, EarlyView.
Electrospun PAN‐MXene nanofibers and yarns integrate enhanced thermal conductivity, photothermal conversion, and triboelectric energy harvesting within a flexible architecture. Interconnected MXene networks promote efficient phonon transport, while their surface chemistry strengthens tribo‐negative behavior, enabling a high power density of 432.7 mW m ...
Ahmadreza Moradi, Piotr K. Szewczyk, Urszula Stachewicz   +2 more
wiley   +1 more source

On the effect of nano calcium carbonate on the flexibility and tensile-shear cracking resistance of greener WMA asphalt concretes containing RAP contents

Case Studies in Construction Materials
Asphalt mixtures are widely used materials for paving roads, however, they need a significant amount of virgin materials, and their preparation process is environmentally unfriendly.
Farman Karimi, Seyed Roohollah Mousavi, Mahmoud Miri   +2 more
doaj   +1 more source

Retracted: Mode I fracture toughness of copper powder compact

Journal of Fundamental and Applied Sciences, 2018
This article was withdrawn and retracted by the Journal of Fundamental and Applied Sciences and has been removed from AJOL at the request of the journal Editor in Chief and the organisers of the conference at which the articles were presented (www.iccmit.net). Please address any queries to editor@jfas.info.
Alabi, A.A., Tahir, S.M., Hanim, M.A.A., Zahari, N.I., Anuar, M.S.   +4 more
openaire   +1 more source

Liquids as Reinforcements for Anisotropic and Tough Soft Matter Composites

Advanced Materials, EarlyView.
Liquid metal droplets are shaped and oriented within soft elastomers to create all‐soft matter composites with programmable mechanical anisotropy. These liquid inclusions act as fiber‐like reinforcements, enabling directional stiffness, enhanced toughness, and controlled crack steering under extreme deformation, offering new routes to resilient soft ...
Gwyneth M. Schloer, Ohnyoung Hur, Ravi Tutika, Aaron Haake, Eric J. Markvicka, Michael D. Bartlett   +5 more
wiley   +1 more source

Hydrogel‐Based 3D‐Printable Stretchable Pressure Sensor

Advanced Materials Technologies, EarlyView.
We present a carbon‐black‐functionalized double‐network granular hydrogel (DNGH) pressure sensor capable of detecting pressures from 200 Pa, equivalent to a light finger touch, up to 500 kPa. The sensor exhibits signal drifts below 3.5% after 800 cycles and response times around 80 ms. Leveraging this broad sensing range, we 3D print this material into
Tianyu Yuan, Chenzhuo Li, Antonia Georgopoulou, John M. Kolinski, Esther Amstad   +4 more
wiley   +1 more source

Investigation on Mode I Fracture Toughness of Woven Carbon Fiber-Reinforced Polymer Composites Incorporating Nanomaterials. [PDF]

Polymers (Basel), 2020
Truong GT, Tran HV, Choi KK.
europepmc   +1 more source

Fracture toughness determination and micromechanics of rock under mode I and mode II loading [PDF]

, 2005
Scientific Technical Report STR; 05 ...
openaire   +3 more sources

Roadmap to Precision 3D Printing of Cellulose: Rheology‐Guided Formulation, Fidelity Assessment, and Application Horizons

Advanced Materials Technologies, EarlyView.
This critical review presents a comprehensive roadmap for the precision 3D printing of cellulose. Quantitative correlations link ink formulation and rheological properties to print fidelity and final material performance. This framework guides the development of advanced functional materials, from biomedical scaffolds to electromagnetic shielding ...
Majed Amini, Hadi Hosseini, Seyyed Alireza Hashemi, Mohammad Arjmand   +3 more
wiley   +1 more source

Experimental investigation of the effects of water content on the anisotropy of mode I fracture toughness of bedded mudstones. [PDF]

PLoS One, 2020
Yang J, Li L, Lian H.
europepmc   +1 more source

3D Printing of Highly Dense and Translucent Zirconia Parts for Dental Applications: Effect of Filament Overlapping

Advanced Materials Technologies, EarlyView.
This study formulated a 5Y‐PSZ zirconia paste for extrusion‐based additive manufacturing via direct ink writing, producing dense ceramic structures for dental applications. A colloidal approach with 47 vol% nanometric powder and tailored additives optimized rheology and printability.
Juliana de Freitas Gouveia Silva, Manuel Fellipe Rodrigues Pais Alves, Ana Carolina da Silva, Tiago Moreira Bastos Campos, Renata Marques De Melo, Susana Maria Henriques Olhero   +5 more
wiley   +1 more source