Results 51 to 60 of about 385,185 (308)
THE EFFECT OF SBR LATEX AND WARM MIX AGENT ON THE PERFORMANCE OF DRY AND WET ASPHALT MIXTURES
Mağallaẗ Al-kūfaẗ Al-handasiyyaẗMoisture damage has been identified as one of the most common causes of distress in asphalt mixes. The attachment between bitumen aggregate components deteriorates when water interacts at the interface, causing the binder to be stripped from the exterior
Ahmed Eltwati +4 more
doaj +1 more source
Advanced ANN Prediction of Moisture Damage in CNT Modified Asphalt Binder [PDF]
Journal of Soft Computing in Civil Engineering, 2017 Moisture penetration causes many direct and indirect distresses in flexible asphalt pavement. Due to damage in asphalt concrete and binder by moisture are the prime concern of failure for flexible pavement worldwide.
Md Arifuzzaman
doaj +1 more source
Risk of climate-induced damage in historical textiles [PDF]
, 2014 Eleven wool and silk historic textiles and two modern artist's canvases were examined to determine their water vapour adsorption, moisture dimensional response and tensile behaviour. All the textiles showed a similar general pattern of moisture response.
Bartosik, M. +8 more
core
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Towards an Alternate Evaluation of Moisture-Induced Damage of Bituminous Materials
Applied Sciences, 2017 Moisture-induced damage is widely known to cause multiple distresses that affect the durability of constructed pavements and eventually lead to the costly maintenance of pavement structures.
Aboelkasim Diab +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates innovative thermoreversible hydrogels derived from S53P4 bioactive glass extracts to aid in the healing of infected diabetic foot wounds. These injectable gels, which gel at body temperature, release beneficial ions and remain stable over time.
Marian G. Vargas Guerrero +9 more
wiley +1 more source
Application of WMA Technology to Bituminous Base Course Mixes
The Baltic Journal of Road and Bridge Engineering, 2018 Warm Mix Asphalt, due to lower mixing and compaction temperatures, provides some engineering benefits over conventional Hot Mix Asphalt. In this study, an attempt is made to assess the viability of using Warm Mix Asphalt technology in bituminous base ...
Rajan Choudhary +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
Assessment of moisture damage susceptibility of asphalt mixtures using thermodynamic properties
Revista Facultad de Ingeniería Universidad de Antioquia, 2013 This paper presents a comparative assessment of the susceptibility to moisture damage for different combinations of Colombian asphalt binders and aggregates.
Silvia Caro-Spinel +1 more
doaj +1 more source