Results 61 to 70 of about 1,951,574 (276)

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Influence of compaction temperature on the resistance of a stabilized granular material with asphalt cement

TecnoLógicas, 2015
The influence of compaction temperature on the mechanical resistance and susceptibility to water of a bound granular material with asphalt cement (called MGEA) was evaluated in laboratory.
Hugo A. Rondón-Quintana, Carlos F. Urazán-Bonells, Saieth B. Chaves-Pabón   +2 more
doaj   +1 more source

Model‐Guided Design of Paper Membrane Architectures for Controlled Flow and Enhanced Diagnostic Sensitivity

Advanced Engineering Materials, EarlyView.
Geometrical modifications on nitrocellulose membranes can result in observable differences in signal intensity relative to a reference membrane (top and bottom left). Using two reference experiments, we have developed a theoretical model that can reproduce the experimentally observed flow changes and provide information on membrane parameters, e.g ...
Maria Dimaki, Lea Holritz, Winnie E. Svendsen   +2 more
wiley   +1 more source

Evaluation of moisture damage for warm mix asphalt (WMA) containing reclaimed asphalt pavement (RAP)

Open Engineering
Warm mix asphalt (WMA) has attracted a lot of interest and attention from the pavement industry since it was introduced as a potential solution to replace traditional hot mix asphalt (HMA).
Mossa Zaineb, Hilal Miami M., Hasan Shatha Sadiq, Fattah Mohammed Y., Hussein Hussein H.   +4 more
doaj   +1 more source

Architecture‐Driven Sensor Stability in Weft‐Knitted Engineering Textiles

Advanced Engineering Materials, EarlyView.
Textile‐integrated sensor architectures are systematically compared to evaluate their electromechanical behavior under combined mechanical and environmental loading. Pocket‐based integration exhibits stable and reproducible signals, whereas tunnel‐based routing shows higher sensitivity accompanied by increased variability.
Adnan Maroof Khan, Johannes Wendler, Dilbar Aibibu, Johannes Mersch, Michael Wöltje, Chokri Cherif   +5 more
wiley   +1 more source

Self‐Cleaning Sensor Surfaces for Long‐Term Environmental Monitoring

Advanced Engineering Materials, EarlyView.
Long‐term use of unattended outdoor sensors without soiling or biofouling is achieved through generation of a micro‐ and nanorough cuvette surface by combing hydrophobic nanoparticles with fluorinated polymers, crosslinked and surface‐attached through CHic chemistry. The coating demonstrates self‐cleaning behavior and prolonged outdoor stability, which
Sanam Kumari Rajak, Yasmina Frey, Ulrike Wallrabe, Oswald Prucker, Jürgen Rühe   +4 more
wiley   +1 more source

Influence of Antistripping Additives and Rejuvenators on Healing Performance of Moisture-Damaged HMA

Advances in Materials Science and Engineering, 2020
This study aims to evaluate the effect of different rejuvenators and antistripping agents on the healing performance of hot mix asphalt (HMA). Two damage HMA series (e.g., moisture damage and aged damage) were subjected to either induction or microwave ...
Dae-Wook Park, Tam Minh Phan, Yeong-Min Kim   +2 more
doaj   +1 more source

Moisture damage in Finnish wooden houses [PDF]

Journal of Building Appraisal, 2005
Finland is one of the world's leading countries in terms of wood construction. Traditionally, wooden houses in Finland have been mainly single-family homes. Since the late 1990s, Finland has invested strongly in wood construction and has tried to increase the use of wood in all types of buildings.
openaire   +1 more source

Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy

Advanced Engineering Materials, EarlyView.
Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang, Jianxiang Zhao, Zhaoqi Chen, Hao Gong, Yinsen Yan, Junlei Tao, Yong Yang   +6 more
wiley   +1 more source

Influence of Coarse Aggregate Geometry and Mineral Composition on the Durability of Asphalt Concrete

Infrastructures
The durability of asphalt concrete is highly dependent on the geometry and mineralogy of coarse aggregates, yet their combined influence on mechanical and moisture resistance properties is still not fully understood.
Hussein K. Mohammad, Amjad H. Albayati, Mazen J. Al-Kheetan   +2 more
doaj   +1 more source