Results 81 to 90 of about 10,559 (261)
Research and Application of Top and Bottom Combined Argon Blowing for 300t Ladle
MetalsThis article uses a water model with a ratio of 1:5.75 to study the influence of factors such as the position and flow rate of top and bottom composite argon blowing on the mixing time of molten steel in a 300t ladle at a certain factory.
Libin Yang +4 more
doaj +1 more source
Advanced Materials, EarlyView.2D α‐Co(OH)2 interleaved with Mo species displays an appealing dual functionality for the production and use of green hydrogen.Mo incorporation greatly benefits the electrochemical behaviour in Oxygen Evolution Reaction for H2 production, while the magnetocaloric response at liquid H2 temperature paves the way for alternative cryogenic refrigerants ...
Daniel Muñoz‐Gil +14 more
wiley +1 more source
Dynamic interaction between refractory and low‐carbon low‐silicon Al‐killed steel
International Journal of Ceramic Engineering & ScienceTo investigate the dynamic interaction between refining refractory and low‐carbon low‐silicon Al‐killed steel, the “refractory‐molten steel‐inclusion” system was analyzed using dynamic erosion experiments and the FactSage database.
Xiang Zhang +5 more
doaj +1 more source
Advanced Materials, EarlyView.Ionic epoxy networks are prepared using ammonium salts as hardeners, leading to a two‐stage curing process with a thermoplastic‐like intermediate. This uncommon behavior enables extrusion and fabrication of thermoplastic prepregs that can be cured into thermoset composites.
Izabela Kurowska +10 more
wiley +1 more source
Corrosion Behavior of 20G and TP347H in Molten LiCl-NaCl-KCl Salt
NanomaterialsThe corrosion behavior of 20G and TP347H materials was investigated in molten LiCl-NaCl-KCl salt. The corrosion rates of these materials in molten chloride salt are high and are strongly affected by the alloying surface oxide formation.
Shijing Xie +7 more
doaj +1 more source
Miniature Soft Robot With Magnetically Reprogrammable Surgical Functions
Advanced Materials, EarlyView.Miniature soft robots have great prospects to revolutionize minimally invasive treatments. Here we present a miniature soft robot, which can be reprogrammed to perform five surgical functionalities with six‐degrees‐of‐freedom motions. This soft robot can prospectively make minimally invasive surgery considerably safer and painless, and enable ...
Chelsea Shan Xian Ng +4 more
wiley +1 more source
Advanced Materials, EarlyView.The perspective presents an integrated view of neuromorphic technologies, from device physics to real‐time applicability, while highlighting the necessity of full‐stack co‐optimization. By outlining practical hardware‐level strategies to exploit device behavior and mitigate non‐idealities, it shows pathways for building efficient, scalable, and ...
Kapil Bhardwaj +8 more
wiley +1 more source
Hydrogel‐Based Airway‐on‐Tube With Perfusable Endothelial Lumen and Outward Epithelialization
Advanced Materials, EarlyView.A hydrogel‐based airway‐on‐tube platform featuring a perfusable endothelial lumen and outward epithelialization is presented. The system supports primary human bronchial epithelial and lung microvascular endothelial coculture under air‐liquid interface conditions.
Ali Doryab +8 more
wiley +1 more source
Advanced Materials, EarlyView.Inspired by the octopus and the golden wheel spider, soft robots with liquid crystal elastomer arc fibers as appendages are fabricated to transcend surface constraints through an elevated center of mass and minimal contact footprints. By leveraging curvature‐encoded deformation‐recovery cycles, these robots exhibit contractile, torsional, and flexural ...
Jong Bin Kim +5 more
wiley +1 more source
On the Decarbonization of Molten Steel
DENKI-SEIKO[ELECTRIC FURNACE STEEL], 1963 openaire +3 more sources