Results 61 to 70 of about 2,342 (259)

Real‐World Safety and Effectiveness of JAK Inhibitors in Systemic Sclerosis: A Propensity‐Matched Study from the EUSTAR Cohort

Arthritis Care &Research, Accepted Article.
Objective JAK inhibitors (JAKis) have shown promising effects in early‐phase studies of SSc. We aimed to assess the safety and explore effectiveness of JAKis compared to conventional immunosuppressants in SSc. Methods A longitudinal retrospective study of the EUSTAR cohort was performed.
Stefano Di Donato, Marie‐Elise Truchetet, Marco Minerba, Oliver Distler, Juan José Alegre Sancho, Yolanda Braun‐Moscovici, Christina Bergmann, Petros Sfikakis, Jeska K de Vries‐Bouwstra, Murray Baron, Silvia Bellando‐Randone, Lorenzo Dagna, Christopher P Denton, Madelon C Vonk, Vanessa Smith, Ivan Castellvi, Gabriela Riemekasten, Andra Balanescu, Masataka Kuwana, Maria De Santis, Kamal Solanki, Anastas Batalov, Vahan Mukuchyan, Marco Matucci‐Cerinic, Yannick Allanore, Francesco Del Galdo, Michael Hughes, EUSTAR Collaborators   +27 more
wiley   +1 more source

Coating of the Lasting Moulds with Hard Alloys

The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science, 2010
This paper presents the researches on the welded coating of lasting moulds used for casting at high melting temperatures. It shows that the coating through the flux welding with the addition of metal powders and graphite leads to a complex properties with a favorable resistance of abrasion and high temperature oxidation resistance compared to other ...
openaire   +1 more source

Mechanochemical Synthesis and Characterization of Nanostructured ErB4 and NdB4 Rare‐Earth Tetraborides

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur, Faruk Kaya, Bora Derin, Mustafa Lütfi Öveçoğlu, Ju Li, Duygu Ağaoğulları   +5 more
wiley   +1 more source

POSSIBILITIES AND RESULTS OF HARDNESS CONTROL OF CAST IRON CASTINGS BY MAGNETIC METHOD AFTER POLAR MAGNETIZATION

Литьë и металлургия, 2007
The correlation dependence between hardness of castings of high-duty cast irons and grey irons, contents of pearlite in metallic mould of high-duty cast iron and parameters CrH of remanent magnetic induction field over surface of castings after ...
S. G. Sandomirskij, V. L. Tsukerman, L. Z. Pisarenko   +2 more
doaj  

The efect of cooling rate on the properties of alloyed cast-iron sizing roll [PDF]

Metalurgija, 2010
Directional heat transfer was investigated by temperature measurements in the casting and in the mould using thermocouples. Measurements were performed in operating conditions during pouring, solidification, and cooling of the casting.
P. Jelić, L. Lazić, J. Črnko
doaj  

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Investigations for modelling hardness of biomedical implant during replication of FDM-based patterns by vacuum moulding

Sādhanā, 2017
In the present work, effort has been made for modelling the microhardness of biomedical implant prepared by combining fused deposition modelling, vacuum moulding and stir casting (SC) process. A dynamic condylar screw (DCS) plate was selected as a real ‘3D’ biomedical implant for this case study.
Rupinder Singh, Gurinder Singh
openaire   +2 more sources

What Do Large Language Models Know About Materials?

Advanced Engineering Materials, EarlyView.
If large language models (LLMs) are to be used inside the material discovery and engineering process, they must be benchmarked for the accurateness of intrinsic material knowledge. The current work introduces 1) a reasoning process through the processing–structure–property–performance chain and 2) a tool for benchmarking knowledge of LLMs concerning ...
Adrian Ehrenhofer, Thomas Wallmersperger, Gianaurelio Cuniberti   +2 more
wiley   +1 more source

Development and Evaluation of Mild Steel Permanent Mould for Al-Alloys Pulley Production

Journal of Materials and Engineering Structures
The development and evaluation of a mild steel permanent mould were conducted with considerations based on materials availability, cost efficiency, and national economic development.
David C. JERRY, Chijioke OKECHUKWU, Cynthia C OKECHUKWU, Joseph ABUTU, Rasheed A. AKINODE   +4 more
doaj  

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source