Results 91 to 100 of about 126,314 (309)
MAIN PROBLEMS OF MOULDING OF SILUMINS. WAYS OF SOLUTION
Литьë и металлургия, 2016 The main problems of silumin’ moulding are connected with insufficient modifying of casting structure, their considerable inclination to gas porosity, difficult to remove nonmetallic inclusions and these features are shown in the article.
E. I. Marukovich, V. Yu. Stetsenko
doaj
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
The Comparison of Chosen - Bonded with the Use of Classical and Dedicated for 3D Printing Furfuryl Binder - Molding Sands’ Properties as a Basis for Development a New Inorganic System [PDF]
Archives of Foundry EngineeringBinder jetting technology (3D printing) in the production of foundry molds and cores is becoming more and more industrially used due to ensuring very good quality of the casting surface. In 3D printing technology as the matrix, quartz sand is mainly used,
D.M. Halejcio, K.A. Major-Gabryś
doaj +1 more source
Fungal Variation during Peanut Paste Storage
International Journal of Microbiology, 2020 Peanut paste produced in multipurpose mills is very often the site of choice for fungal contaminants that pose a major risk to consumers. The objective of this study is to evaluate the level of fungal contamination of peanut paste produced according to ...
Zamblé Bi Irié Abel Boli +3 more
doaj +1 more source
The influence of fibre length and concentration on the properties of glass fibre reinforced polypropylene : 6. the properties of injection moulded long fibre PP at high fibre content [PDF]
, 2005 The results of an investigation of the mechanical performance of injection moulded long glass fibre reinforced polypropylene with a glass fibre content in the range 0-73 weight % are presented. The composite modulus exhibited a linear dependence on fibre
Thomason, J.L.
core +1 more source
Production of MgO/TiC Composites From MgO‐C Recyclates Using Spark Plasma Sintering
Advanced Engineering Materials, EarlyView.Using the spark plasma sintering technique, MgO/TiC composites are manufactured from recycled MgO‐C refractories stemming from the steel production that were mixed with titanium powder. This article shows, how the size of the Ti grains and their distribution in the powder mixture affect the local carbon concentration in TiC.
Jiayan Yu +3 more
wiley +1 more source
Thermo-Insulating Moulding Sand for thin Walled Castings
Archives of Metallurgy and Materials, 2014 In paper the selection of the composition and determination of main properties of novel moulding sand was described. The mail goal was to create moulding sand characterized by high thermal insulating properties in relations with low specific weight. This
Cholewa M., Szuter T.
doaj +1 more source
Bioinspired Shape‐Memory Hook Fasteners With Programmable Interlocking and Silent Release
Advanced Engineering Materials, EarlyView.Bioinspired hook fasteners made from epoxy shape‐memory polymers are shown to switch between strong, secure attachment and gentle, silent release when heated. By combining programmable geometry and material response, these adaptive fasteners outperform commercial systems in strength and noise control, enabling new solutions for robotics, medical ...
Maria I. Vallejo Ciro +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Viktoriia Shtefan, Thorgund Nemec, Ute Hempel, Annett Gebert and coworkers demonstrate that anodic treatment of Ti–Cu‐based metallic glass in a nontoxic pyrophosphate electrolyte forms a protective bilayered Ti/Zr‐oxide film enriched with Cu nanocrystals.
Viktoriia Shtefan +8 more
wiley +1 more source
Archives of Metallurgy and Materials, 2015 The harmfulness assessment of moulding sands with a geopolymer binder and a new hardener, in an aspect of the emission of substances from the BTEX group, was performed.
Bobrowski A. +3 more
doaj +1 more source