Results 71 to 80 of about 126,314 (309)

Time dependent properties of thermoplastic protein produced from bloodmeal with sodium sulphite as an anti-crosslinking agent [PDF]

, 2012
The aim of this research was to investigate how the time dependent mechanical behaviour of bloodmeal-based thermoplastic was affected by varying sodium sulphite content at two injection moulding temperatures (120°C at exit or 140°C at exit ...
Bier, James Michael, Lay, Mark C., van der Merwe, De Wet, Verbeek, Casparus Johan R.   +3 more
core   +3 more sources

Corrosion and Process Analysis of a Preoxidized MgO Recyclate‐Based Cermet Anode in Laboratory‐Scale Na‐Cryolite Molten Salt Electrolysis of Aluminum at 1000°C

Advanced Engineering Materials, EarlyView.
EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk, Farhan Hossain, Felipe A. Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source

The thermal and structural analysis of new bicomponent binders for moulding sands consisting of furfuryl resin and polycaprolactone (PCL)

Archives of Metallurgy and Materials, 2017
The aim of the article is thermal and structural analysis of new two-component binders for foundry moulding sands. The previous research showed the possibility of using biodegradable materials as binders or parts of binders’ compositions for foundry ...
Major-Gabryś K., Bobrowski A., Grabarczyk A., Dobosz St. M.   +3 more
doaj   +1 more source

The Effect of Injection Moulding Temperature on PET Particles/Fibrils in Blends and MFCs [PDF]

, 2016
The microfibrillar composites of polypropylene (PP)/poly(ethylene terephthalate) (PET) have been prepared by twin-screw extrusion, followed by cold drawing. The employed stretch ratio was 4.
Cardon, Ludwig, Delva, Laurens, Kuzmanović, Maja, Ragaert, Kim   +3 more
core   +1 more source

Assessment Method of Overheating Degree of a Spent Moulding Sand with Organic Binder, After the Casting Process [PDF]

, 2013
A proper management of sand grains of moulding sands requires knowing basic properties of the spent matrix after casting knocking out. This information is essential from the point of view of the proper performing the matrix recycling process and ...
Dańko R.
core   +1 more source

Raman Spectroscopic Identification of Oxide Phases in a Corroded MgO–Steel Composite Anode Used in Aluminum Molten Salt Electrolysis

Advanced Engineering Materials, EarlyView.
Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler, Serhii Yaroshevskyi, Alexander Adamczyk, Mahnaz Mehdizadehlima, Julia Richter, Cameliu Himcinschi, David Rafaja, Alexandros Charitos, Christos G. Aneziris, Jens Kortus   +9 more
wiley   +1 more source

Rheological Properties of Typical Ceramic Slurries Used in the Lost Wax Technology

Archives of Foundry Engineering, 2017
The results of investigations of the rheological properties of typical ceramic slurries used in the investment casting technology - the lost wax technology are presented in the paper. Flow curves in the wide range of shear velocity were made.
Kolczyk J., Jamrozowicz Ł., Kaźnica N.
doaj   +1 more source

Interaction of MgO Recyclate‐Based Cermet Anode With KF‐AlF3‐Al2O3 at 800°C During Laboratory Scale Aluminum Molten Salt Electrolysis

Advanced Engineering Materials, EarlyView.
A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain, Alexander Adamczyk, Felipe Alejandro Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source

Influence of the Al2O3 Solid Phase on the Kinetics of Binding Ceramic Moulds

Archives of Foundry Engineering, 2017
The investigation results of the kinetics of binding ceramic moulds, in dependence on the solid phase content in the liquid ceramic slurries being 67, 68 and 69% - respectively, made on the basis of the aqueous binding agents Ludox AM and SK.
Kolczyk J., Zych J., Jamrozowicz Ł.
doaj   +1 more source

Interaction of Ladle Slag With Varying SiO2 Content and Recyclate‐Based MgO–C Refractories

Advanced Engineering Materials, EarlyView.
Ladle slags (CaO/Al2O3 = 1) with 1–20 wt% SiO2 were investigated in contact with industrial MgO–C refractories fabricated from fresh magnesia and 50 wt% recyclate. The sessile drop method at 1600°C reveals intensive gas formation, delayed slag infiltration in recyclate‐based samples, and, under high‐SiO2 slag, formation of a dense MgAl2O4‐rich ...
Anton Yehorov, Eldar Salpagarov, Anhelina Mospan, Till Manon Jannis Stadtmüller, Thomas Schemmel, Christos Georgios Aneziris, Olena Volkova   +6 more
wiley   +1 more source