Results 61 to 70 of about 47,967 (247)
Strong Lead‐Free Bioinspired Piezoceramics for Durable Energy Transducers
Advanced Functional Materials, EarlyView.We fabricated brick‐and‐mortar lead‐free piezoceramics with Bi0.5Na0.5TiO3 monocrystal platelets as bricks and amorphous silica as mortar. The alignment of the bricks and the presence of the amorphous silica led to anisotropic residual stresses. These residual stresses increase the samples toughness, strength and durability while the brick alignment ...
Ruxue Yang +12 more
wiley +1 more source
Optimization of the investment casting process
Metalurgija, 2012 Rapid prototyping is an important technique for manufacturing. This work refers to the manufacture of hollow patterns made of polymeric materials by rapid prototyping technologies for its use in the preparation of ceramic molds in the investment casting ...
M. Martinez-Hernandez +4 more
doaj
An Edible Chitosan‐Based Acoustic Sensor for Sound‐Responsive Actuation in Edible Robots
Advanced Functional Materials, EarlyView.This study introduces an edible acoustic sensor for robotic food and edible robotics. Built from a chitosan piezoelectric film between gold electrodes, the sensor enables acoustic communication through ON/OFF keying. Integrated into an edible robot with pneumatically actuated arms and neck, it responds to high‐frequency tones.
Valerio Francesco Annese +8 more
wiley +1 more source
Analysis of rheological behaviour of titanium feedstocks formulated with a water-soluble binder system for powder injection moulding [PDF]
, 2014 Binder selection and formulation are critical in powder injection moulding. Binders play a key role in controlling the rheological properties of a feedstock and influence whether the resulting feedstock can be successfully injection moulded, debound and ...
Pickering, Kim L. +3 more
core +1 more source
Quality Index of the AlSi7Mg0.3 Aluminium Casting Alloy Depending on the Heat Treatment Parameters
Archives of Foundry Engineering, 2016 Issues connected with high quality casting alloys are important for responsible construction elements working in hard conditions. Traditionally, the quality of aluminium casting alloy refers to such microstructure properties as the presence of inclusions
Czekaj E. +3 more
doaj +1 more source
Advanced Functional Materials, EarlyView.A dynamically actuated reconfigurable topographical surface (DARTS) integrates contact‐mediated bactericidal nanotopography with programmable mechanical actuation to actively disrupt bacterial biofilms. Dynamic surface reconfiguration enhances bacterial killing and suppresses implant‐associated infections in vivo, providing a new strategy for active ...
Mohammad Asadi Tokmedash +4 more
wiley +1 more source
Optimisation of Continuous and Pulsed Cooling in Injection Moulding Processes [PDF]
, 2007 The concept of pulsed cooling in injection moulding involves cycling the flow of coolant in order that cooling only takes place as and when it is required, as opposed to continuous cooling, where the coolant in run through the channels throughout the ...
B. A. McCalla +14 more
core +1 more source
MAIN PROBLEMS OF MOULDING OF SILUMINS. WAYS OF SOLUTION
Литьë и металлургия, 2016 The main problems of silumin’ moulding are connected with insufficient modifying of casting structure, their considerable inclination to gas porosity, difficult to remove nonmetallic inclusions and these features are shown in the article.
E. I. Marukovich, V. Yu. Stetsenko
doaj
Bone‐Inspired Recyclable Composites for Damage‐Tolerant Circular Materials
Advanced Functional Materials, EarlyView.Bone‐inspired architected composites are developed by combining osteon‐like reinforcements with a recyclable Elium thermoplastic matrix. The hierarchical architecture redirects cracks and promotes energy dissipation, while enabling recovery of intact, aligned, load‐bearing reinforcement units that retain their original stiffness, revealing a route ...
Alessandro Stagni +4 more
wiley +1 more source
Sandwich injection moulding with thermoset materials [PDF]
This project aimed to study the feasibility of making a thermoset sandwich injection moulding from a novel thermoset co-injection moulding system. Two thermoset polyesters, BMC and a powder coating, were used for all experiments.
Kiatmanaroj, Subongkoj
core