Results 81 to 90 of about 17,470 (285)
CFD Applications in Energy Engineering Research and Simulation: An Introduction to Published Reviews [PDF]
, 2019 Computational Fluid Dynamics (CFD) has been firmly established as a fundamental discipline to advancing research on energy engineering. The major progresses achieved during the last two decades both on software modelling capabilities and hardware ...
Iranzo Paricio, Jose Alfredo
core +1 more source
Top‐Down Fabricated Wood‐Derived Pressure and Strain Sensors: A Review
Advanced Science, EarlyView.This review focuses on wood‐derived pressure/strain sensors fabricated via top‐down strategies. It analyzes wood's structural composition, examines processing techniques, discusses sensor types and sensing mechanisms, and reviews existing research. The article concludes with future directions for enhancing performance and scalability.
Yi Ren +8 more
wiley +1 more source
Third harmonic current injection into highly saturated multi-phase machines
Archives of Electrical Engineering, 2017 One advantage of multi-phase machines is the possibility to use the third harmonic of the rotor flux for additional torque generation. This effect can be maximised for Permanent Magnet Synchronous Machines (PMSM) with a high third harmonic content in the
Klute Felix, Jonsky Torben
doaj +1 more source
FPGA Implementation of a General Space Vector Approach on a 6-Leg Voltage Source Inverter [PDF]
, 2011 A general algorithm of a Space Vector approach is implemented on a 6-leg VSI controlling a PM synchronous machine with three independent phases. In this last case, the necessity of controlling the zero-sequence current motivates the choice of a special ...
BRUYERE, Antoine +6 more
core +6 more sources
Transforming Grain‐Boundary Brittle Precipitates to Ductility Pathways in Complex Concentrated Alloy
Advanced Science, EarlyView.By engineering graded BCC/L12 interfaces, brittle precipitates in a complex concentrated alloy enable sequential deformation, realizing gigapascal strength with >20% elongation to solve the strength‐ductility trade‐off. ABSTRACT Conventional wisdom holds that hard grain‐boundary (GB) precipitates embrittle structural alloys by acting as crack ...
Zhixin Li +14 more
wiley +1 more source
IEEE Access, 2020 Integrated on-board battery chargers (OBCs) have been recently introduced as an optimal/elegant solution to increase electric vehicle (EV) market penetration as well as minimize overall EV cost. Unlike conventional off-board and on-board battery chargers,
Mohamed Y. Metwly +5 more
doaj +1 more source
, 2019 Mesoscopic simulations of hydrocarbon flow in source shales are challenging, in part due to the heterogeneous shale pores with sizes ranging from a few nanometers to a few micrometers.
Andrew, Matthew +9 more
core +1 more source
A General Mathematical Formulation for the Determination of Differential Leakage Factors in Electrical Machines with Symmetrical and Asymmetrical Full or Dead-Coil Multiphase Windings [PDF]
, 2018 This paper presents a simple and general mathematical formulation for the determination of the differential leakage factor for both symmetrical and asymmetrical full and dead-coil windings of electrical machines.
Caruso M. +4 more
core +1 more source
Advanced Science, EarlyView.A CoCrFeNiTa0.4 eutectic high‐entropy alloy achieves a near‐theoretical yield strength of 2.6 GPa with 13.6% plasticity. This breakthrough stems from a hierarchical nanostructure (FCC‐Laves lamellae with L12/D022 precipitates), which alleviates the inter‐phase modulus/hardness mismatch through synergistic strengthening and toughening, guiding the ...
Yusha Luo +10 more
wiley +1 more source
Comparative Analysis of Fault-Tolerant Dual-Channel BLDC and SR Motors
Energies, 2019 This article presents the results of a comparative analysis of two electronically commutated brushless direct current machines intended for fault-tolerant drives.
M. Korkosz +4 more
doaj +1 more source