Results 171 to 180 of about 1,694,794 (371)

Enhanced Fog Water Harvesting on Superhydrophobic Steel Meshes

Advanced Engineering Materials, EarlyView.
Fog harvesting using mesh designs offers a sustainable solution to water scarcity. This study highlights key considerations for fog harvesting research and develops a methodology for a standardized protocol reflecting fog characteristics and environmental conditions.
Pegah Sartipizadeh, Mohammad Reza Mohammadizadeh, Carlo Antonini, Raziyeh Akbari   +3 more
wiley   +1 more source

Monitoring and Maintaining Laser Surface Texture Quality Based on Acoustic and Optical Process Emissions during Direct Laser Interference Patterning

Advanced Engineering Materials, EarlyView.
Acoustic emissions during direct laser interference patterning are shown to strongly correlate with surface texture depth. By implementing a closed‐loop control system utilizing acoustic feedback, consistent microstructures with uniform depth are achieved despite laser power fluctuations.
Tobias Steege, Frederic Schell, Adrian Belkin, Christoph Zwahr, Andrés F. Lasagni   +4 more
wiley   +1 more source

Neuromuscular recovery using calcium protease inhibition after median nerve repair in primates.

, 1989
Marie A. Badalamente, Lawrence C. Hurst, A. Stracher   +2 more
openalex   +1 more source

Lateral cutaneous nerve of the thigh pain in association with inguinal hernia repair [PDF]

, 2003
Richard G. Davies, Graham Arthurs
openalex   +1 more source

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

Transient Hypoglossal Nerve Palsy after General Anesthesia in Beach Chair Position for Shoulder Arthroscopic Bankart Repair: A case report [PDF]

, 2004
Won Joon Choi, Hong Kyun Shin, Dong-Ok Kim, Sung Wook Park, Doo Ik Lee, Dong Soo Kim   +5 more
openalex   +1 more source

Effects of Creep in Titanium at Room Temperature during Tensile and Profilometry‐Based Indentation Plastometry Testing

Advanced Engineering Materials, EarlyView.
This article concerns room temperature tensile testing, with a range of (nominal) strain rates, of three titanium alloys. Stress–strain curves are analyzed to obtain creep characteristics. Profilometry‐based indentation plastometry testing is also covered, using different penetration velocities, and correlations established with tensile data.
Philip John McKeown, James Rees Miller, Trevor William Clyne   +2 more
wiley   +1 more source

Sustainable biomedical microfibers from natural products

Aggregate
Microfibers from natural products are endowed with remarkable biocompatibility, biodegradability, sustainable utilization as well as environmental protection characteristics etc.
Jiahui Guo, Xinyue Cao, Zhiqiang Luo, Yujuan Zhu, Yuanjin Zhao, Xiaosong Gu   +5 more
doaj   +1 more source

Experimental study of motor nerve repair: Comparison of nylon suture and two component fibrin adhesive techniques.

, 1988
Shigeki Nishihira
openalex   +2 more sources

Low‐Velocity Penetration Impact Behavior of Triply Periodic Minimal Surface Strut‐Based Lattices

Advanced Engineering Materials, EarlyView.
Triply periodic minimal surface (TPMS)‐based lattices are gaining attention for their multifunctional properties in applications as aeronautics and automotive, which involve low‐velocity impact loading. This work evaluates the low‐velocity penetration impact behavior of five distinct TPMS architectures.
Lucía Doyle, Javier García‐Molleja, Carlos González   +2 more
wiley   +1 more source