Results 91 to 100 of about 79,942 (257)

Functional differential equations of third order

Electronic Journal of Differential Equations, 2005
In this paper, we consider the third-order neutral functional differential equation with distributed deviating arguments. We give sufficient conditions for the oscillatory behavior of this functional differential equation.
Tuncay Candan, Rajbir S. Dahiya
doaj  

Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam

Advanced Engineering Materials, EarlyView.
Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva, Joseph Lavoie, Afsaneh Rabiei   +2 more
wiley   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

Advanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel, Prashant K. Purohit, Jordan R. Raney   +2 more
wiley   +1 more source

Existence of solutions for nonlinear impulsive neutral integro-differential equations of Sobolev type with nonlocal conditions in Banach spaces

Electronic Journal of Differential Equations, 2013
In this article, we prove the existence of mild and strong solutions for nonlinear impulsive integro-differential equations of Sobolev type with nonlocal initial conditions.
Bheeman Radhakrishnan, Aruchamy Mohanraj, Velu Vinoba   +2 more
doaj  

Positive Solutions for a Higher-Order Nonlinear Neutral Delay Differential Equation

Abstract and Applied Analysis, 2011
This paper deals with the higher-order nonlinear neutral delay differential equation (dn/dtn)[x(t)+∑i=1mpi(t)x(Ti(t))]+(dn−1/dtn−1)f(t,x(α1(t)),…,x(αk(t)))+h(t,x(β1(t)),…,x(βk(t)))=g(t), t≥to, where n,m,k∈ℕ, pi,τi,βj,g∈C([to,+∞),ℝ), αj∈Cn−1([to,+∞),ℝ), f∈
Zeqing Liu, Ming Jia, Jeong Sheok Ume, Shin Min Kang   +3 more
doaj   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Influence of Fe Particle Size Distribution on Chemical Homogeneity, Microstructure, and Crack Formation in Fe–SiC Powder Blends Processed by PBF‐LB/M

Advanced Engineering Materials, EarlyView.
The influence of Fe particle size on in situ alloying of Fe–SiC powder blends in PBF‐LB/M is revealed. Contrary to expectations, the coarser Fe fraction provides a broader crack‐free processing window and slightly improved elemental homogeneity while producing higher but more variable hardness. The results highlight a complex trade‐off between particle
Anna Luise Strauch, Anastasiya Toenjes, Matthias Steinbacher   +2 more
wiley   +1 more source

Printed Integrated Logic Circuits Based on Chitosan‐Gated Organic Transistors for Future Edible Systems

Advanced Functional Materials, EarlyView.
Edible electronics needs integrated logic circuits for computation and control. This work presents a potentially edible printed chitosan‐gated transistor with a design optimized for integration in circuits. Its implementation in integrated logic gates and circuits operating at low voltage (0.7 V) is demonstrated, as well as the compatibility with an ...
Giulia Coco, Valerio Francesco Annese, Valerio Galli, Ilaria Penna, Debora Russo, Marina Veronesi, Rita Scarpelli, Stefania Sabella, Mario Caironi   +8 more
wiley   +1 more source

Laser‐Induced Graphene from Waste Almond Shells

Advanced Functional Materials, EarlyView.
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova, Anna Chiara Bressi, Marina Galliani, Attilio Marino, Gianni Ciofani, Eduardo Machado‐Charry, Hilda Gomez Bernal, Alessandra Francini, Luca Sebastiani, Francesco Greco   +9 more
wiley   +1 more source