Results 1 to 10 of about 24,512 (259)
Beneficial Effect of Pt and of Pre-Oxidation on the Oxidation Behaviour of an NiCoCrAlYTa Bond-Coating for Thermal Barrier Coating Systems [PDF]
, 2011 The oxidation behaviour of a thermal barrier coating (TBC) system is a major concern as the growth of the thermally grown oxide (TGO) layer on the bondcoating creates stresses that greatly favour the thermal barrier spallation.
Monceau, Daniel +4 more
core +3 more sources
Research Progress on the Melting Process of Nickel-based Superalloy
Teshugang, 2023 The melting method of nickel-based superalloy is the decisive factor related to the alloy quality. Vacuum induction melting can effectively control the content of O， N， H and other gases and harmful impurities in alloy ingots， and accurately control the ...
Yang Hao, Wang Fangjun, Li Cai, Wu Wei
doaj
Advanced burner-rig test for oxidation-corrosion resistance evaluation of MCrAlY/superalloys systems [PDF]
, 2006 Protective coatings are used on gas turbine components to enable them to survive in engine-operating conditions. This study presents a recently developed cyclic burner-rig test that is used to simulate helicopter engine conditions and to assess the ...
Andrieu, Eric +3 more
core +3 more sources
Hot extrusion characteristics and technique optimization for superalloy 617B tube
工程科学学报, 2019 Nickel-base superalloy 617B is one of the most promising candidates for superheater and reheater pipes of advanced ultra-supercritical (AUSC) power plants.Hot extrusion is a key process during the manufacturing of superalloy 617B pipes.However, the high ...
JIANG He, DONG Jian-xin, ZHANG Mai-cang
doaj +1 more source
Clean recycling of spent nickel-based single-crystal superalloy by molten magnesium
Journal of Materials Research and TechnologyNickel-based single-crystal superalloys are designed for extreme conditions due to their superior corrosion and creep resistance properties. However, these pose challenges in the subsequent recycling after reaching their end-of-life. Molten magnesium (Mg)
Hao Li +6 more
doaj +1 more source
Materials & Design, 2019 The uniaxial tensile tests are performed to study flow behavior of a nickel-based superalloy with different initial microstructures at an intermediate temperature range (473–973 K).
Y.C. Lin +3 more
doaj +1 more source
Journal of Aeronautical MaterialsNickel-based superalloys are important structural materials in turbine engines and gas turbines，but their conventional fabrication processes are complex，costly and have poor raw-material-utilization rate.
QIAN Huxiao +4 more
doaj +1 more source
SUPERALLOYS: AN INTRODUCTION WITH THERMAL ANALYSIS
Journal of Fundamental and Applied Sciences, 2015 Nickel based superalloys are commonly used materials in the aero industry and more specifically in the hot section of aero engines. These nickel and nickel iron based superalloys are precipitation strengthened alloys with a face centered cubic gamma ...
S. S. Raza
doaj +1 more source
Evolution of interfacial dislocation network during anisothermal high-temperature creep of a nickel-based superalloy [PDF]
, 2011 The effect of thermal cycling creep on the dislocation networks at the γ/γ′ interfaces in the MC2 superalloy is investigated. Tensile creep tests were performed under thermal cycling and isothermal conditions at low stress (80 MPa) and high temperature ...
Coujou, Armand +4 more
core +4 more sources
Silicon-slurry/aluminide coating [PDF]
, 1983 A low cost coating protects metallic base system substrates from high temperatures, high gas velocity ovidation, thermal fatigue and hot corrosion and is particularly useful fo protecting vanes and blades in aircraft and land based gas turbine engines. A
Deadmore, D. L., Young, S. G.
core +1 more source