Results 21 to 30 of about 566,690 (302)
Selection of cutting parameters for the machinability of Inconel 718 using Grey Relational Analysis
MATEC Web of Conferences, 2018 Inconel 718 is considered to be most difficult to machine superalloy because of its high shear strength, work hardening and precipitation hardening. Abrasive particles which are in microstructure have tendency have forming chip to be welded to tool and ...
Sunit Rout Ivan, Pal Pandian P.
doaj +1 more source
Nondestructive examination of recovery stage during annealing of a cold-rolled low-carbon steel using eddy current testing technique [PDF]
, 2017 The recovery process in steel is usually investigated by conventional destructive tests that are expensive, time-consuming and also cumbersome. In this study, an alternative non-destructive test technique (based on eddy current testing) is used to ...
Davis, Claire +4 more
core +1 more source
MATEC Web of Conferences, 2018 Additive Manufacturing (AM) is a reliable technique to build multifunctional components with any complex geometry. The present paper assesses the role of two vital AM techniques, namely Selective Laser Sintering (SLS) and Selective Laser Melting (SLM) in
Jayakumar Arunkumar
doaj +1 more source
Rekayasa Sipil, 2019 To make the examination of the strength of existing building structures easier, can be done by using the NDT methods. It is therefore a study related to the combination of NDT and DT methods to obtain better accuracy of the results.
Bagas Bhanu Aribawa +2 more
doaj +1 more source
System of Non-Destructive Testing [PDF]
Interdisciplinary Description of Complex Systems : INDECS, 2009 In this paper the initial analysis of NDT laboratory is presented by means of agent-based modelling. For the purpose of analysis, laboratory is taken into account as a complex system consisting of three agents; equipment, personnel and specimens. Interaction between the agents is circular.
Morana Lisièar +2 more
openaire +3 more sources
A COMPREHENSIVE REVIEW ON THE NON-DESTRUCTIVE TEST FOR POLYMER MATRIX COMPOSITE
Rekayasa Mesin, 2023 Polymer matrix composite (PMC) is widely applied in structural engineering mainly due to its high strength-to-weight ratio. Of many benefits, the transportation industry uses this type of material mainly due to its high strength-to-weight ratio.
Ari Wahjudi, Agung Sugeng Widodo
doaj +1 more source
Mathematics, 2022 The present study provides a correlation and regression analysis of lightweight waste aggregate concretes with varying degrees of fibre reinforcement. The concrete mix contains pre-soaked red ceramic waste aggregate, expanded clay coarse aggregate and ...
Marie Horňáková, Petr Lehner
doaj +1 more source
Non-Destructive Inspection of Impact Damage in Composite Aircraft Panels by Ultrasonic Guided Waves and Statistical Processing. [PDF]
, 2017 This paper discusses a non-destructive evaluation (NDE) technique for the detection of damage in composite aircraft structures following high energy wide area blunt impact (HEWABI) from ground service equipment (GSE), such as heavy cargo loaders and ...
Capriotti, Margherita +3 more
core +2 more sources
Investigation of Diagnostic Techniques for Metal Oxide Surge Arresters [PDF]
, 2005 Gapless metal oxide surge arresters(MOSA)have been available in the market for many years since they were first introduced in the 1970's. The aim of this study is to investigate some reliable diagnostic techniques to assess the condition of a metal oxide
Mardira, Karl P. +2 more
core +1 more source
Non-destructive test of steel structures by conical indentation
MATEC Web of Conferences, 2017 The problem of mechanical properties measurement of steel structures by non-destructive method of impact cone indentation is considered. The method is based on analytical solution and experimental data of a problem of impact indentation by cone into ...
Beskopylny Alexey +3 more
doaj +1 more source