Results 101 to 110 of about 237,918 (305)

Study of the nature of non-metallic inclusions in samples of aluminum and silicon killed low carbon steels, collected in the refining treatment and continuous casting stages

Materials Research, 2004
The amount, distribution, size and chemical composition of non-metallic inclusions have a direct influence on steel properties. By controlling size and chemical composition of these inclusions, it is possible to get a product with good quality.
José Carlos Santos Pires, Amauri Garcia
doaj   +1 more source

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

Numerical Investigation of Outflow of Non-Metallic Inclusions during Steel Refining in the Ladle. [PDF]

Materials (Basel), 2022
Migas P, Ślęzak M, Karbowniczek M, Szczęch S, Hornik A.   +4 more
europepmc   +1 more source

Bistable Mechanisms 3D Printing for Mechanically Programmable Vibration Control

Advanced Engineering Materials, EarlyView.
This work introduces a 3D‐printed bistable mechanism integrated into tuned mass dampers (TMDs) for mechanically adaptive passive vibration suppression. Through optimized geometry, the bistable design provides adaptable vibration reduction across a broad range of scenarios, achieving effective vibration mitigation without complex controls or external ...
Ali Zolfagharian, Frédéric Demoly, Mohammad Lakhi, Bernard Rolfe, Mahdi Bodaghi   +4 more
wiley   +1 more source

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Effect of Microstructure on Wear Resistance of Low-Alloy High-Strength Wear-Resistant Steel

International Journal of Electrochemical Science, 2019
In this paper, microstructure, corrosion resistance and wear resistance of low-alloy high-strength wearresistant steels of NM400 and KN400X were studied. It is found that the wear resistance of these steels differed from each other significantly although
Dongting Wu, Hui Zhang, Shushuai Liu, Yuanxiao Li, Zhiqiang Li, Yong Zou   +5 more
doaj   +1 more source

Evolution of the Numerical Model Describing the Distribution of Non-Metallic Inclusions in the Tundish. [PDF]

Materials (Basel), 2021
Merder T, Pieprzyca J, Warzecha M, Warzecha P, Hutny A.   +4 more
europepmc   +1 more source

Evaluation of the Potential of Laser Shock Peening Compared with Cold Expansion for Improving Fatigue Resistance of Riveted Lap Joints of Aerospace Grade 7175 Al Alloy

Advanced Engineering Materials, EarlyView.
This study investigates laser shock peening for enhancing fatigue performance of riveted aerospace aluminum joints. A comparative approach with cold expansion combines fatigue testing and synchrotron X‐ray methods. Integrating mechanical testing with residual stress and strain characterization provides insights into how different treatments affect the ...
Ogün Baris Tapar, David Osman Busse, Maximilian Sprengel, Domenico Furfari, Marc‐André Nielsen, Guilherme Abreu Faria, Jérémy Epp   +6 more
wiley   +1 more source

Adjustment of Coatings Morphology and Particle Distribution of Layered Silicates by Freeze‐Drying for Improved Gas Barriers

Advanced Engineering Materials, EarlyView.
Freeze‐drying of layered silicate is the key to get coatings with superior gas barrier. Freeze‐drying of layered silicates modified with dodecylamine (DDA) is a highly effective technique for the preparation of barrier pigments that significantly mitigate the permeation of oxygen, water vapor, and hydrogen through polymer films containing these ...
Joshua Lommes, Moritz Bätcher, Andrea Deißenberger, Volkmar Stenzel, Andreas Hartwig   +4 more
wiley   +1 more source