Results 111 to 120 of about 76,322 (245)

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source

Resistance Rapid Heating of Aluminum Coatings in an Extreme High Vacuum–Adequate Atmosphere for Hot Stamping

Advanced Engineering Materials, EarlyView.
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht, Alexander Schnettger, Ulrich Holländer, Sven Hübner, Bernd‐Arno Behrens, Hans Jürgen Maier   +5 more
wiley   +1 more source

Research on trajectory optimization of Delta robot in food production lines based on improved MOEA/D algorithm

Shipin yu jixie
ObjectiveBy optimizing the sorting trajectory of Delta robots, while ensuring sorting accuracy, this paper aims to reduce comprehensive energy consumption, shorten operating time, and minimize operational impact.MethodsBased on the analysis of automated ...
ZHU Hui, ZHAO Shufeng, LI Rucheng, LIU Fei   +3 more
doaj   +1 more source

Numerical Algorithms for Non-smooth Optimization Applicable to Seismic Recovery

, 2013
Inverse problems in seismic tomography are often cast in the form of an optimization problem involving a cost function composed of a data misfit term and regularizing constraint or penalty. Depending on the noise model that is assumed to underlie the data acquisition, these optimization problems may be non-smooth.
openaire   +2 more sources

A Knowledge‐Based Approach for Understanding and Managing Additive Manufacturing Data

Advanced Engineering Materials, EarlyView.
Additive manufacturing processes generate a large amount of data. Effectively managing, understanding, and retrieving information from this data remains a major challenge. Therefore, we propose an ontology‐based approach to integrate heterogeneous data, enable semantic queries, and support decision‐making.
Mina Abd Nikooie Pour, Prithwish Tarafder, Anton Wiberg, Huanyu Li, Johan Moverare, Patrick Lambrix   +5 more
wiley   +1 more source

Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May, Finn‐Lennard Janthur, Lena Kreie, Michael Müller, Sarah Seffer, Nick Schwarz, Jörg Hermsdorf, Thomas Hassel, Stefan Kaierle, Ludger Overmeyer   +9 more
wiley   +1 more source

Bibliography on non-differentiable optimization and non-smooth analysis

Journal of Computational and Applied Mathematics, 1981
AbstractThis bibliography lists about four hundred references to published papers, theses, and books which deal with non-differentiable optimization problems or contribute to the field of (non-convex) non-smooth analysis useful for the study of such optimization problems.
openaire   +1 more source

Impact of Pre‐Oxidation Treatments on a Recycled MgO/Steel‐Composite as Carbon Free Anode in Aluminum‐Electrolysis Environments

Advanced Engineering Materials, EarlyView.
Cermets (60 vol.% AISI 316L stainless steel, 40 vol.% recycled MgO), intended for use in aluminum electrolysis, were pre‐oxidized in three furnaces with different heating technologies and subjected to a cryolite corrosion test. The different atmospheres influenced the formation of oxide layers, which in turn affected corrosion resistance and ...
Patricia Kaiser, Felix Drechsler, Nora Brachhold, Florian Kerber, Christos G. Aneziris   +4 more
wiley   +1 more source

Affecting the Properties of Copper–Graphene Electroconductive Composite by Severe Plastic Deformation

Advanced Engineering Materials, EarlyView.
Copper‐based composites enhanced with carbon feature convenient mechanical properties and favorable electric conductivity. Processing via deformation and thermomechanical treatments can introduce advantageous microstructures further enhancing their performance. Herein, copper–graphene powder‐based composites are directly consolidated via rotary swaging
Radim Kocich, Lenka Kunčická, Pavel Czernek, Zifan Wang   +3 more
wiley   +1 more source

A Topology Optimization Framework for the Inverse Design of Nonlinear Mechanical Metamaterials

Advanced Engineering Materials, EarlyView.
This work uses topology optimization to design unit cells for mechanical metamaterials with a prescribed nonlinear stress–strain response. The framework adds contact and postbuckling modeling to synthesize microstructures for three highly nonlinear responses, including pseudoductile behavior, monostable with snap‐through buckling, and bistable ...
Charlie Aveline, Matthew Santer, Robert Hewson   +2 more
wiley   +1 more source