Results 161 to 170 of about 233,549 (265)

Robust Spot Melting by 3D Spot Arrangements in Electron Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This work proposes an approach to replace separately melted contours for spot melting in electron beam powder fusion. Adapting the spot arrangements close to the contour combined with stacking yields a comparable surface quality without the inherent challenges of separate contours, as demonstrated, by electron optical images and roughness measurements.
Tobias Kupfer, Lukas Spano, Sebastian Pohl, Carolin Körner, Matthias Markl   +4 more
wiley   +1 more source

Fostering Innovation: Streamlining Magnetocaloric Materials Research by Digitalization

Advanced Engineering Materials, EarlyView.
Magnetocaloric cooling (MCE) is an environmentally friendly refrigeration method with great potential. Optimizing MCE materials involves the preparation and screening of large quantities of samples, which in turn generates a large amount of data. A digitalization approach is presented that uses ontologies, knowledge graphs, and digital workflows to ...
Simon Bekemeier, Moritz Blum, Luana Caron, Alisa Chirkova, Philipp Cimiano, Basil Ell, Inga Ennen, Michael Feige, Maik Gaerner, Thomas Hilbig, Andreas Hütten, Günter Reiss, Tapas Samanta, Sonja Schöning, Christian Schröder, Lennart Schwan, Chris Taake, Martin Wortmann   +17 more
wiley   +1 more source

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source

Tailoring Functional Properties of Ti–Ni–Cu Shape Memory Alloy Thin Films for MEMS Actuators

Advanced Engineering Materials, EarlyView.
A comprehensive study of critical parameters required to develop well‐performing Ti–Ni–Cu thin film shape memory alloy microactuators is provided. Materials science and device integration aspects are integrated by addressing structural and physical relationships using complementary characterization techniques as well as a practical fabrication solution
Elaheh Akbarnejad, Aleksander Kostka, Gowtham Arivanandhan, Yujiao Li, Alan Savan, Manfred Kohl, Alfred Ludwig   +6 more
wiley   +1 more source

Non-Thermal Processing of Food

, 2010
openaire   +2 more sources

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Editorial: Incorporating non-thermal technologies to enhance food fortification strategies: current trends and future directions in personalized nutrition. [PDF]

Front Nutr
Nasiru MM, Muhammad AI, Boateng EF.
europepmc   +1 more source

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source

A Comprehensive Review on Non-Thermal Technologies in Food Processing & Implementation in Different Food Industries: Limitations and Challenges. [PDF]

Food Sci Nutr
Raza A, Abdullah HM, Wasiq M, Butt MU, Afzaal M, Singh A, Panigrahi R, Shah MA.   +7 more
europepmc   +1 more source