Results 191 to 200 of about 198,480 (259)
Some of the next articles are maybe not open access.
Journal of Thermal Analysis and Calorimetry, 2022
M. Vivekanandan +4 more
semanticscholar +1 more source
M. Vivekanandan +4 more
semanticscholar +1 more source
AIAA Journal, 2002
A polytropic analytical equation system for the internal e ow of nozzles and ducts has been developed by a solution to the combined friction/area change compressible e ow equations. Validation of the system is sought through comparison with experimental data and numerical simulations using FLUENT in the prediction of the performances of two ...
E. A. Wilson, D. Adler, P. Bar-Yoseph
openaire +1 more source
A polytropic analytical equation system for the internal e ow of nozzles and ducts has been developed by a solution to the combined friction/area change compressible e ow equations. Validation of the system is sought through comparison with experimental data and numerical simulations using FLUENT in the prediction of the performances of two ...
E. A. Wilson, D. Adler, P. Bar-Yoseph
openaire +1 more source
Rocket nozzles: 75 years of research and development
Sādhanā, 2021Shivangi Khare, U. Saha
semanticscholar +1 more source
Journal of Spacecraft and Rockets, 1971
An analytical method is presented for the design of axisymmetric annular nozzles to yield uniform and axial flow. Computed results are used to display typical matched inner and outer contours, the effects of major initial flow variables, and the resulting wall forces.
openaire +1 more source
An analytical method is presented for the design of axisymmetric annular nozzles to yield uniform and axial flow. Computed results are used to display typical matched inner and outer contours, the effects of major initial flow variables, and the resulting wall forces.
openaire +1 more source
The Effect of Nozzles and Nozzle Loadings on Shell Buckling
Volume 3: Design and Analysis, 2015This paper investigates the effect of nozzles and nozzle loadings on the overall buckling capacity of a vessel subject to external pressure designed to ASME VIII Div 1. ASME VIII Div 1 provides a well-established design-by-rule (DBR) approach for vessels subject to external pressure, but this takes no consideration for the presence of ...
Edward Clarke, Robert Frith
openaire +1 more source
Experimental investigation of serpentine nozzles for turbofan
, 2021Zhong Hui +4 more
semanticscholar +1 more source
Aggregate Breakup in a Contracting Nozzle
Langmuir, 2009The breakup of dense aggregates in an extensional flow was investigated experimentally. The flow was realized by pumping the suspension containing the aggregates through a contracting nozzle. Variation of the cluster mass distribution during the breakage process was measured by small-angle light scattering.
M. Soos +3 more
openaire +4 more sources
Model tests with nozzles and steering nozzles for trawlers1
International Shipbuilding Progress, 1965With a trawler model several nozzle propeller arrangements were tested in still water both free running and when trawling. Special attention was paid to turning ability and rudder head torques to be expected with steering nozzles.
openaire +1 more source
Truncated Perfect Nozzles in Optimum Nozzle Design
ARS Journal, 1961A graphical technique for selecting optimum nozzle contours from a family of truncated perfect nozzles is presented which permits simultaneous consideration of various types of optima. This procedure includes the effects of friction, as well as the thermodynamic properties of the reacting gas.
J. H. AHLBERG +3 more
openaire +1 more source
AIAA Journal, 1998
During the sea-level ignition process of rocket motors, the nozzle is subjected to an overexpanded e ow condition that can cause high side loads. Prediction of the symmetrical separation location is the e rst key step to a determination of the range of possible side-load magnitudes.
openaire +1 more source
During the sea-level ignition process of rocket motors, the nozzle is subjected to an overexpanded e ow condition that can cause high side loads. Prediction of the symmetrical separation location is the e rst key step to a determination of the range of possible side-load magnitudes.
openaire +1 more source