Results 11 to 20 of about 460,410 (304)

The Nylon Scintillator Containment Vessels for the Borexino Solar Neutrino Experiment [PDF]

, 2007
Borexino is a solar neutrino experiment designed to observe the 0.86 MeV Be-7 neutrinos emitted in the pp cycle of the sun. Neutrinos will be detected by their elastic scattering on electrons in 100 tons of liquid scintillator. The neutrino event rate in
A. Goretti, A. Ianni, A. Nelson, A. Pocar, A. Sonnenschein, Alimonti, Alimonti, Alimonti, An. Ianni, Apollonio, Arpesella, Back, Baginski, Baginski, Bahcall, Boehm, Boger, Bonetti, C. Galbiati, Chen, E. de Haas, E. Harding, Elisei, F. Calaprice, F. Loeser, Galbiati, Heusser, J. Benziger, K. McCarty, Kiko, L. Cadonati, Leung, Liu, M. Leung, Martin, Oberauer, Pocar, R. Fernholz, R. Ford, R. Parsells, R.B. Vogelaar, S. Kidner, Smirnov, Smirnov, Strumia, T. Shutt, Wolfenstein, Wójcik, Wójcik, Zuzel   +49 more
core   +3 more sources

Microbial abilities to degrade global environmental plastic polymer waste are overstated

Environmental Research Letters, 2022
Internationally, the environmental damage caused by the improper disposal of approximately 100 Mt of plastic waste per annum is of growing concern. Attempts to address this issue have generated many hundreds of scientific studies announcing the discovery
G Lear, S D M Maday, V Gambarini, G Northcott, R Abbel, J M Kingsbury, L Weaver, J A Wallbank, O Pantos   +8 more
doaj   +1 more source

Mineralizing Coating on 3D Printed Scaffolds for the Promotion of Osseointegration

Frontiers in Bioengineering and Biotechnology, 2022
Design and fabrication of implants that can perform better than autologous bone grafts remain an unmet challenge for the hard tissue regeneration in craniomaxillofacial applications. Here, we report an integrated approach combining additive manufacturing
Abshar Hasan, Abshar Hasan, Abshar Hasan, Romain Bagnol, Robert Owen, Robert Owen, Arsalan Latif, Hassan M. Rostam, Sherif Elsharkawy, Felicity R. A. J. Rose, Felicity R. A. J. Rose, José Carlos Rodríguez-Cabello, Amir M. Ghaemmaghami, David Eglin, David Eglin, Alvaro Mata, Alvaro Mata, Alvaro Mata   +17 more
doaj   +1 more source

Performance enhancement of nylon/Kevlar fiber composites through viscoelastically generated pre-stress [PDF]

, 2013
Kevlar-29 fibers have high strength and stiffness but nylon 6,6 fibers have greater ductility. Thus by commingling these fibers prior to molding in a resin, the resulting hybrid composite may be mechanically superior to the corresponding single fiber ...
Cao, Cohen, Cui, Daynes, Fancey, Fancey, Fancey, Fancey, Faur-Csukat, Fazal, Fazal, Hadi, Hine, Hufenbach, Jang, Knoester, Lafitte, Mertiny, Motahhari, Motahhari, Pang, Pang, Pang, Pang, Thanomsilp, Timoshenko, Wisnom   +26 more
core   +1 more source

Impact behaviour of nylon-rubber blends: 5. Influence of the mechanical properties of the elastomer [PDF]

, 1989
Blends of 90wt% nylon-6 and 10wt% impact modifier were prepared. As impact modifiers were used: EPDM (ethylene propylene diene monomer) rubber, EPM (ethylene propylene monomer) rubber, polyethylene, four poly(ether esters) and some commercial impact ...
Borggreve, R.J.M., Gaymans, R.J., Schuijer, J.   +2 more
core   +3 more sources

PLASTIC / NYLON WASTE POLLUTION AND DISPOSAL IN OYO STATE, NIGERIA

Russian Journal of Agricultural and Socio-Economic Sciences, 2021
This study examined the effect of plastic/nylon pollution, the disposal method and the factors influencing the methods of disposal in Oyo state. This study was conducted in eleven local government areas (LGA) of Oyo states using structured questionnaire ...
Bolaji K.A., Kabir G.B., Adebayo D.O., Oguntoye T.O.   +3 more
doaj   +1 more source

Flexible Thermoplastic Denture Base Materials for Aesthetical Removable Partial Denture Framework [PDF]

Journal of Clinical and Diagnostic Research, 2013
Conventional fixed partial dentures, implant supported Fixed Partial Dentures (FDPs) and removable partial dentures are the most common treatment modalities for the aesthetic and functional rehabilitation of partially edentulous patients.
Kunwarjeet Singh, Himanshu Aeran, Narender Kumar, Nidhi Gupta   +3 more
doaj   +1 more source

Probing polymer chain constraint and synergistic effects in nylon 6-clay nanocomposites and nylon 6-silica flake sub-micro composites with nanomechanics [PDF]

, 2015
In this study, we report that a synergistic effect exists in the surface mechanical properties of nylon 6–clay nanocomposites (NC) that can be shown by nanomechanical testing.
Beake, BD, Bell, GA, Chen, J, Gao, F, Tait, Y   +4 more
core   +1 more source

Effect of Denture Base Material on the Peri-implant Stresses of Implant Supported Overdenture: An In Vitro Study [PDF]

International Journal of Prosthodontics and Restorative Dentistry
Purpose: The purpose of this study was to evaluate the effect of denture base material on the peri-implant stresses of overdentures held in place by inclined and straight implants during axial dislodgments.
Hossam M Bassiouny, Ehab M Atito, Wesam E Badr, Mohamed A Elmaroush, Mohamed A Quassem   +4 more
doaj   +1 more source

Effects of Degree of Particle Melt and Crystallinity in SLS Nylon-12 Parts [PDF]

, 2008
Differential Scanning Calorimetry (DSC) traces for SLS Nylon-12 parts display two distinct melt peaks, which have been related to the presence of both melted and crystallised regions, and un-melted particle cores within the part.
Hopkinson, N., Majewski, C. E., Zarringhalam, H.   +2 more
core   +1 more source