Results 131 to 140 of about 67,391,839 (291)

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Architecture‐Driven Sensor Stability in Weft‐Knitted Engineering Textiles

Advanced Engineering Materials, EarlyView.
Textile‐integrated sensor architectures are systematically compared to evaluate their electromechanical behavior under combined mechanical and environmental loading. Pocket‐based integration exhibits stable and reproducible signals, whereas tunnel‐based routing shows higher sensitivity accompanied by increased variability.
Adnan Maroof Khan, Johannes Wendler, Dilbar Aibibu, Johannes Mersch, Michael Wöltje, Chokri Cherif   +5 more
wiley   +1 more source

An Innovative Internal Calibration Strategy and Implementation for LT-1 Bistatic Spaceborne SAR

Remote Sensing
Bistatic and multistatic SAR technology, with its multi-dimensional, ultra-wide swath, and high-resolution advantages, is widely used in earth observation, military reconnaissance, deep space exploration, and other fields.
Yuanbo Jiao, Kaiyu Liu, Haixia Yue, Heng Zhang, Fengjun Zhao   +4 more
doaj   +1 more source

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source

Non‐Additive Criteria Assessment in Sustainability Evaluation of High Entropy Alloys: A Toxicity‐Weighted Framework

Advanced Engineering Materials, EarlyView.
Sustainability assessment requires methodologies that appropriately distinguish between additive and non‐additive material properties. A toxicity‐weighted scoring system is developed and applied that accounts for the disproportionate influence of highly toxic constituents through nonlinear weighting functions, providing more realistic estimates than ...
Seth Mehalic, Oladele A. Ogunseitan, Julie M. Schoenung   +2 more
wiley   +1 more source

Aquarius Radiometer Performance: Early On-Orbit Calibration and Results [PDF]

, 2012
The Aquarius/SAC-D observatory was launched into a 657-km altitude, 6-PM ascending node, sun-synchronous polar orbit from Vandenberg, California, USA on June 10, 2011.
Piepmeier, Jeffrey R., Yueh, Simon H., LeVine, David M., Ruf, Christopher, Wentz, Frank   +4 more
core  

Controlling Grain Growth in Powder Bed Fusion of Yttria‐Stabilized Zirconia Using Femtosecond Lasers: Challenges and Methodological Insights

Advanced Engineering Materials, EarlyView.
Binder‐free laser powder bed fusion of 8YSZ with a femtosecond laser is used to map process windows linking scan strategy, heat accumulation, and grain growth. Time‐resolved thermography and simulations reveal thermal regimes that enable continuous, vitrified, and fine‐grained 8YSZ surface layers without absorptive additives and demonstrate ...
Markus Kühn, Sarah Kaden, Andrea Barz, Daniel Störzner, Jens Bliedtner, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Simulation‐Based Analysis of Insert Pull‐Out in Nickel‐Polyurethane Hybrid Foams Using CT‐Derived Geometries

Advanced Engineering Materials, EarlyView.
CT‐based finite element simulations combined with in situ X‐ray computed tomography are used to analyze insert pull‐out in nickel‐coated polymer foams. Despite variations in material parameters, deformation consistently concentrates within a narrow annular region around the insert.
Yannik Bautz, Jonas Fell, Hendrik Jost, Stefan Diebels, Hans‐Georg Herrmann   +4 more
wiley   +1 more source

Linearity Assessment from the Plankton, Aerosol, Cloud, and Ocean Ecosystem Ocean Color Instrument Pre-Launch Testing and On-Orbit Operations

Remote Sensing
Satellite observations have become increasingly important in scientific studies of the Earth’s climate, especially for oceanographic science. A next generation sensor known as the Ocean Color Instrument (OCI) was launched in February 2024 onboard the ...
Jeff McIntire, Gerhard Meister, Julia A. Barsi, Ulrik Gliese, Kim Jepsen, Samuel Kitchen-McKinley, Shihyan Lee   +6 more
doaj   +1 more source

Gallium Microalloying in Bi–Sn Solders: Interfacial Phase Formation, Wettability, and Long‐Term Shear Reliability Under Isothermal Aging

Advanced Engineering Materials, EarlyView.
Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová, Markéta Klimtová, Mohd Faizul Mohd Sabri, Yew Hoong Wong, Petr Veselý, Martin Plaček, Karel Dušek   +6 more
wiley   +1 more source