Results 121 to 130 of about 4,851,207 (310)

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

open access: yesAdvanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller   +3 more
wiley   +1 more source

All-optical reshaping of constant-envelope signals

open access: yes, 2009
We propose a simple optical circuit based on parallel limiting-amplification in SOAs for the regeneration of WDM signals that are constant envelope and direct-detected.
PRESI, Marco   +5 more
core   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

open access: yesAdvanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel   +2 more
wiley   +1 more source

Optical Properties of GaN Thin Flim

open access: yesIraqi Journal of Physics, 2009
GaN thin films were deposited by thermal evaporation onto glass substrates at substrate temperature of 403 K and a thickness of 385 nm . GaN films have amorphous structure as shown in X-ray diffraction pattern .
Salma M. Shaban
doaj  

Electrodeposition in Structural Lattices of Variable Architectures

open access: yesAdvanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon   +3 more
wiley   +1 more source

Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel

open access: yesAdvanced Engineering Materials, EarlyView.
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe   +9 more
wiley   +1 more source

Multidimensional modulation formats for coherent optical communications

open access: yes, 2016
Coherent optical communication systems applying modulation formats with a dimensionality of four or higherare investigated and compared to systems using conventional formats. Higher dimensionality can be achieved by applying modulation over more than one
Agrell, Erik   +8 more
core   +1 more source

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

open access: yesAdvanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo   +15 more
wiley   +1 more source

Microstructural Evolution and In Situ Formation of TiB and TiC in Ti─5Al─2.5Sn Alloy Processed by Powder Metallurgy

open access: yesAdvanced Engineering Materials, EarlyView.
Accelerated in situ formation of TiB and TiC in Ti–5Al–2.5Sn–B4C is driven by transient liquid phase formation, which enhances particle reactions and microstructural evolution. This process increases hardness and establishes a coupled relationship between sintering temperature and reinforcement content, strongly influencing porosity in the resulting ...
Fernando. Y. Kojima, Juliano. Soyama
wiley   +1 more source

Home - About - Disclaimer - Privacy