Results 141 to 150 of about 3,946,788 (277)

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Elinvar Materials: Recent Progress and Challenges

Advanced Engineering Materials, EarlyView.
Elinvar materials, exhibiting temperature‐invariant elastic modulus, are critical for precision instruments and emerging technologies. This article reviews recent progress in the field, with a focus on the anomalous thermoelastic behavior observed in key material systems.
Wenjie Li, Yang Ren
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

Dielectric Barrier Discharge Plasma Deoxidation of Natively Oxide Layer of Copper Powders in a Fluidized Bed

Advanced Engineering Materials, EarlyView.
This paper presents a novel approach to reducing oxide layers on metal powders using low‐temperature hydrogen dielectric barrier discharge plasmas at atmospheric pressure. Unlike conventional hydrogen‐plasma reductions, the powders do not contact the plasma directly.
Shukang Zhang, Annett Wollmann, Thomas Gimpel, Alfred P. Weber   +3 more
wiley   +1 more source

Unraveling the Effect of Tramp Elements on Phase Transformations in Steels by Combining CALPHAD Modeling and Experiments

Advanced Engineering Materials, EarlyView.
This study investigates how tramp elements from increased scrap usage influence phase transformations in low‐alloyed steel. Combining dilatometry and microscopy reveal that tramp elements delay transformations, reduce critical cooling rates and increase hardenability.
Lukas Hatzenbichler, Daniel Marian Ogris, Phillip Haslberger, Matthew Galler, Oleksandr Glushko, Ronald Schnitzer   +5 more
wiley   +1 more source

Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading

Advanced Engineering Materials, EarlyView.
The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley   +1 more source

Instantaneous p-q power Theory for compensating nonsinusoidal systems

Instantaneous p-q power Theory for compensating nonsinusoidal systems
identifier:oai:t2r2.star.titech.ac.jp ...
openaire  

Understanding the Stochastic Nature of Process Parameter Development of Blown Powder Laser Beam Directed Energy Deposition Additive Manufacturing of Pure Molybdenum

Advanced Engineering Materials, EarlyView.
Identified through the use of statistical design of experiments and metallographic investigation, this study exposes the stochastic origins of intergranular cracks in blown powder laser beam directed energy deposition additive manufacturing of pure molybdenum. It further demonstrates a successful crack mitigation approach with direct correlation to the
Nathaniel J. Lies, Daniel E. Driemeyer, Aaron P. Stebner   +2 more
wiley   +1 more source