Results 111 to 120 of about 3,120 (211)

Booklet for Standard Operational Procedures of DFG SPP2122 Interlaboratory Study measuring the effect of nanoparticles on the entire PBF-LB process chain of AlSi10Mg and PA12 [PDF]

An interlaboratory study (ILS) has been designed within the DFG Priority Program 2122 “Materials for Additive Manufacturing” (SPP 2122) for testing nanoparticle-modified and virgin AlSi10Mg and PA12 powder feedstocks along the entire process chain of ...
Kuşoğlu, Ihsan Murat, Ziefuß, Anna Rosa, Barcikowski, Stephan   +2 more
core   +1 more source

Comparative analysis of a 3D printed polymer bonded magnet composed of a TPU-PA12 matrix and Nd-Fe-B atomised powder and melt spun flakes respectively

Journal of Materials Research and Technology
The present study reports the development of new polymer bonded magnet containing a Thermoplastic Polyurethane (TPU) – Nylon (PA12) blend as the matrix material and Nd-Fe-B magnetic particles.
Granit Hajra, Mihael Brunčko, Leo Gusel, Ivan Anžel   +3 more
doaj   +1 more source

PPS/PA12摻合系統之相界面相容性反應研究與分析 [PDF]

, 2014
本論文主要是研究在PPS/PA12摻合系統中, 加入反應性單體 MAH 及Styrene, 使得這兩種單體能藉由原位(In-situ)反應的方式, 在相界面間原位生成(In-situ formation)所需要的相容劑。並藉由熱溶洗出連續相的方法, 收集分散相, 以FTIR做相界面共聚物含量的定量分析。而動態機械分析(DMA)及微觀相型態(SEM)等測試, 則被用來探討相界面共聚物含量對摻合系統所造成的影響。研究結果發現:在PPS/PA12(30/70)摻合系統中, 加入MAH及Styrene單體 ...
林達鎔; 黃清俊
core  

Injection moulding of PA12: influence of processing history on the thermal and mechanical behaviour [PDF]

, 2018
The presented PhD thesis will summarise the work conducted on the influence of different processing histories, due to either process settings or mould geometry, on the thermal and mechanical behaviour of injection moulded Polyamide 12 (PA12), currently ...
Tino Meyer (7121657)
core  

FATIGUE CHARACTERISTICS OF 3D-PRINTED CARBON FIBER NYLON 12 (CF/PA12) HIP IMPLANTS

Academy Journal of Science and Engineering
Carbon fiber composite materials are frequently employed in components where cyclic loads could result in fatigue failure. The primary objective of this study was to assess the fatigue behavior of fused modelled, carbon fiber nylon 12 (CF/PA12) hip ...
Gaudence N., Maxime B., Venant K., Eustache H., Bernard M., Emmanuel B.   +5 more
doaj  

Laser-Based Polishing of Additively Manufactured PA12 and PAEK Polymer Components Using a Robotic System. [PDF]

Polymers (Basel)
Uluz E, Metz L, Hedwig L, Bremen S.
europepmc   +1 more source

Corrosion Behaviour of Injection- and Compression-Moulded Nd-Fe-B and Sm-Fe-N Magnets with Different Polymer Binders. [PDF]

Polymers (Basel)
Lešić N, Kovačević N, Milošev I.
europepmc   +1 more source

Feasibility Study of Suitable Surface Treatments for 3D-Printed Parts to Increase Abrasion Resistance Stability. [PDF]

Polymers (Basel)
Fink D, Chval Z, Raz K.
europepmc   +1 more source

Fatigue behaviour of laser-sintered PA12 specimens under four-point rotating bending [PDF]

Purpose – The purpose of this paper was twofold: first, to determine if rotating bending could be used as an effective way of determining thefatigue behaviour of laser-sintered nylon, and second, to examine whether the fatigue behaviour of laser-sintered
Dalgarno K, Munguia J
core  

Graphene Oxide (GO) Impregnation of Polyamide-Based Composites Enhances Thermal Conductivity After Selective Laser Sintering. [PDF]

Nanomaterials (Basel)
Koshlakova VA, Stepashkin AA, Maurino V, Muratov DS.   +3 more
europepmc   +1 more source