Results 151 to 160 of about 241,419 (292)
Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma
Advanced Engineering Materials, EarlyView.The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source
Advanced Engineering Materials, EarlyView.The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm +6 more
wiley +1 more source
Adaptive quality of service for packet loss reduction using OpenFlow meters. [PDF]
PeerJ Comput SciDeo K, Chaudhary K, Assaf M.
europepmc +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
Mitigating Effects of Packet Loss in Wireless Neural Data Transfer: Exploring the Influence of Low-Cost Recovery Methods on Spikes and HFOs in iEEG. [PDF]
Conf Proc (Midwest Symp Circuits Syst)Ayyoubi AH +6 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Low‐consumable nickel ferrite‐based anodes for the Hall–Héroult process are compared with conventional prebaked carbon anodes using thermodynamic simulation and prospective life cycle assessment under contrasting future electricity system pathways from 2025 to 2050.
Felipe Alejandro Garcia Paz +6 more
wiley +1 more source
Interaction of Ladle Slag With Varying SiO2 Content and Recyclate‐Based MgO–C Refractories
Advanced Engineering Materials, EarlyView.Ladle slags (CaO/Al2O3 = 1) with 1–20 wt% SiO2 were investigated in contact with industrial MgO–C refractories fabricated from fresh magnesia and 50 wt% recyclate. The sessile drop method at 1600°C reveals intensive gas formation, delayed slag infiltration in recyclate‐based samples, and, under high‐SiO2 slag, formation of a dense MgAl2O4‐rich ...
Anton Yehorov +6 more
wiley +1 more source