Results 91 to 100 of about 1,152,225 (287)

Microfabrication of Microlens by Timed-Development-and-Thermal-Reflow (TDTR) Process for Projection Lithography

open access: yesMicromachines, 2020
This paper presents a microlens fabrication process using the timed-development-and-thermal-reflow process, which can fabricate various types of aperture geometry with a parabolic profile on a single substrate in the same batch of the process.
Jun Ying Tan   +2 more
doaj   +1 more source

Hybrid Semi‐Transparent Perovskite‐Photovoltaics and Concentrated Solar‐Thermal Harvesting Collectors

open access: yesAdvanced Science, EarlyView.
A hybrid semi‐transparent perovskite‐photovoltaic and concentrating solar‐thermal collector is developed to spectrally split sunlight for simultaneous electricity and heat generation. The design achieves thermal decoupling between the photovoltaic and thermal components, offering a promising route for efficient co‐harvesting of solar electricity and ...
Nada. A. Alati   +8 more
wiley   +1 more source

Curved Casimir Operators and the BGG Machinery

open access: yesSymmetry, Integrability and Geometry: Methods and Applications, 2007
We prove that the Casimir operator acting on sections of a homogeneous vector bundle over a generalized flag manifold naturally extends to an invariant differential operator on arbitrary parabolic geometries.
Andreas Cap, Vladimír Soucek
doaj  

Co‐Design Insights for Mechanically Active Flexible Printed Circuit Boards Through the CurveQuad Origami Robot

open access: yesAdvanced Science, EarlyView.
This paper presents the process of integrating electronics directly into the body sheet of CurveQuad, a small origami robot that can self‐fold, crawl, and steer with a single actuator. The authors design a flexible printed circuit board for the body sheet: the key challenge is to navigate how embedding electronics affects the mechanical properties and ...
Xuelin Wu   +6 more
wiley   +1 more source

Effect of Reflector Geometry in the Annual Received Radiation of Low Concentration Photovoltaic Systems

open access: yesEnergies, 2018
Solar concentrator photovoltaic collectors are able to deliver energy at higher temperatures for the same irradiances, since they are related to smaller areas for which heat losses occur.
João Paulo N. Torres   +6 more
doaj   +1 more source

Courant Algebroids in Parabolic Geometry

open access: yes, 2011
24 pages. v3: Added Section 4.3.
Armstrong, Stuart, Lu, Rongmin
openaire   +2 more sources

Synthesis Route‐Controlled Atomic Ordering Optimizes Thermoelectric Transport in Bi2SbSe3

open access: yesAdvanced Science, EarlyView.
Atomic ordering modulation enhancing the thermoelectric performance of Bi2SbSe3. The solid‐state synthesis route redistributes Sb atoms between the Bi2Se3 quintuple layers and the Bi bilayers in the BiSe structure, resulting in a more disordered Bi2SbSe3 than the one‐pot synthesized counterpart.
Xiaoqian Wang   +18 more
wiley   +1 more source

Coexistence of Large Nernst Effect and Axis‐Dependent Conduction Polarity in Semimetal MoSi2

open access: yesAdvanced Electronic Materials, EarlyView.
MoSi2${\rm MoSi}_2$ is a rare material in which axis‐dependent conduction polarity (ADCP) and a large ordinary Nernst effect (ONE) coexist. The pronounced ONE (199μVK−1$199\,\umu \mathrm {V}\,\mathrm {K}^{-1}$) originates from nearly perfect carrier compensation, high mobility, and likely phonon drag, while ADCP arises from mixed‐dimensionality of the ...
Orest Pavlosiuk, Maciej J. Winiarski
wiley   +1 more source

Some differential complexes within and beyond parabolic geometry

open access: yes, 2018
For smooth manifolds equipped with various geometric structures, we construct complexes that replace the de Rham complex in providing an alternative fine resolution of the sheaf of locally constant functions.
Eastwood, MG   +3 more
core  

Fast Homoepitaxy on (100) β‐Ga2O3 Substrates With Large Grown‐In Offcut

open access: yesAdvanced Electronic Materials, EarlyView.
(100) β‐Ga2O3 substrates with grown‐in offcuts eliminate grinding waste. A 13.7° offcut in the [‐c] direction produces vertical (001) sidewalls, ideal for 3D architectures. Increasing the offcut angle from 0° to 13.4° continually increases growth rate up to 30x, and step‐flow growth is maintained.
M. Brooks Tellekamp   +9 more
wiley   +1 more source

Home - About - Disclaimer - Privacy