Results 111 to 120 of about 214,445 (299)

Domain-Adaptive Transformer Partial Discharge Recognition Method Combining AlexNet-KAN with DANN

Sensors
The changes in operating conditions of a power transformer can cause a shift in the distribution of partial discharge data, leading to the gradual generation of unlabeled new data, which results in the degradation of the original partial discharge ...
Jianfeng Niu, Yongli Zhu
doaj   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Reduction of Oxide Inclusions During the High‐Frequency Welding of Steel via a Nonthermal Ar/H2 Plasma Jet

Advanced Engineering Materials, EarlyView.
High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin, Lienhard Wegewitz, René Gustus, Henning Wiche, Wolfgang Maus‐Friedrichs   +4 more
wiley   +1 more source

Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma

Advanced Engineering Materials, EarlyView.
The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie, David Kramer, Thomas Scheithauer, Hans Jürgen Maier, Thomas Hassel   +4 more
wiley   +1 more source

Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres

Advanced Engineering Materials, EarlyView.
This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann, René Gustus, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +3 more
wiley   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

Advanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios, Anthony Gonzalez, Aleksander Aleman, Tyler Dolmetsch, Tanaji Paul, Arvind Agarwal   +5 more
wiley   +1 more source

Identification of partial discharges in cable terminals of high-speed EMUs based on fuzzy C-means clustering

机车电传动
As an effective means to diagnose the insulation status of on-board cable terminals, partial discharge detection faces strong interference in the actual operating environment of trains. To address this issue, this paper proposed a strategy for separating
YANG Yanhua, CEHN Zhenbao, CAO Han, ZHANG Yanlin, LIU Kai, CHEN Kui, GAO Guoqiang   +6 more
doaj  

Accurate Identification Partial Discharge of Cable Termination for High-Speed Trains Based on S-Transform and Two-Dimensional Convolutional Network Algorithm

Sensors
Cable termination is an important part of energy transmission in high-speed trains, and it is also a weak link in the insulation. It is important to determine the insulation status of cable terminals by the detection results of partial discharge signals,
Yunlong Xie, Peng You, Guangning Wu, Tingyu Zhang, Yang Luo, Shuyuan Zhou, Kai Liu, Kui Chen, Dongli Xin, Guoqiang Gao   +9 more
doaj   +1 more source

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

Advanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source