Results 141 to 150 of about 30,911 (308)
IET Science, Measurement & TechnologyPartial discharge (PD) detection is an important technique for monitoring and evaluating the insulation condition of gas‐insulated switchgear (GIS) equipment.
Feng Chen +5 more
doaj +1 more source
, 2018 Partial discharges (PD) measurement provide valuable information for assessing the condition of the insulation elements in high voltage (HV) electrical grids. During the last three decades, several instruments integrated with specific technical functionalities have been developed in order to perform accurate diagnostics when temporary or monitoring ...
openaire +2 more sources
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Partial Discharges and Noise Discrimination Using Magnetic Antennas, the Cross Wavelet Transform and Support Vector Machines. [PDF]
Sensors (Basel), 2020 Muñoz-Muñoz F, Rodrigo-Mor A.
europepmc +1 more source
Consumed by Abdominal Distention
Arthritis Care &Research, EarlyView.
Abimbola Fadairo‐Azinge +3 more
wiley +1 more source
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, EarlyView.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source
Analysis of partial discharges
, 2019 Předkládaná diplomová práce je zaměřena především na analýzu částečných výbojů a výbojů neúplných při napájení stejnosměrným zdrojem napětí. Popsán je princip vzniku těchto výbojů jak při stejnosměrném napětí, tak při napětí střídavém a jejich důsledky v
Čelovský, Filip
core
Computer Simulation of Partial Discharges in Voids inside Epoxy Resins Using Three-Capacitance and Analytical Models. [PDF]
Polymers (Basel), 2020 Rodríguez-Serna JM +3 more
europepmc +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying
Advanced Engineering Materials, EarlyView.An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara +8 more
wiley +1 more source