Results 81 to 90 of about 713,475 (259)

Genetic variability for yield and related traits among wild accessions of cowpea and cross-compatibility with cultivated accessions

Agricultura Tropica et Subtropica
Cowpea is an important legume, and its wild relatives could be reliable sources of favorable alleles for genetic diversity and improvement of important traits.
Olayiwola Richard Oluseyi, Taiwo Bolaji Samuel, Oyetunde Oyeboade Adebiyi, Ariyo Omolayo Johnson   +3 more
doaj   +1 more source

Correlation and path coefficient analysis for yield and quality traits under organic fertilizer management in rice (Oryza sativa L.) [PDF]

Electronic Journal of Plant Breeding, 2014
An investigation was carried out in 32 rice genotypes to understand the association among fourteen contributing traits for yield and quality and their direct and indirect influence on the grain yield under organic fertilizer management.
Dhurai S. Y., D. Mohan Reddy And Pradeep Kumar Bhati
doaj  

A Knowledge‐Based Approach for Understanding and Managing Additive Manufacturing Data

Advanced Engineering Materials, EarlyView.
Additive manufacturing processes generate a large amount of data. Effectively managing, understanding, and retrieving information from this data remains a major challenge. Therefore, we propose an ontology‐based approach to integrate heterogeneous data, enable semantic queries, and support decision‐making.
Mina Abd Nikooie Pour, Prithwish Tarafder, Anton Wiberg, Huanyu Li, Johan Moverare, Patrick Lambrix   +5 more
wiley   +1 more source

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Rafting of Ni‐Based Superalloys Under Multiaxial Load as Understood by Phase‐Field Simulations and Critical Experiments

Advanced Engineering Materials, EarlyView.
Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan, David Bürger, Gunther Eggeler, Oleg Shchyglo, Ingo Steinbach, Muhammad Adil Ali   +5 more
wiley   +1 more source

Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading

Advanced Engineering Materials, EarlyView.
The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley   +1 more source

Response of rice (Oryza sativa L.) genotypes under aerobic conditions [PDF]

Electronic Journal of Plant Breeding, 2011
A field experiment was conducted during wet season 2009 to study the response of rice genotypes under aerobic conditions.Variance studies revealed significant differences among the genotypes for the traits, days to flowering, plant height, harvestindex ...
Keshava Murthy B. C, Arvind Kumar and Shailaja Hittalmani
doaj  

Time‐Dependent Oxidation and Scale Evolution of a Wrought Co/Ni‐Based Superalloy

Advanced Engineering Materials, EarlyView.
This study shows how a new wrought Co/Ni‐based superalloy resists oxidation at 800 ∘$^\circ$C. The oxide scale changes from rough, fast‐growing spinel to a dense, protective chromia–alumina layer. Atom probe analysis reveals tiny refractory‐rich bubbles at the interface that mark the transition to long‐term, diffusion‐controlled protection ...
Cameron Crabb, Zachary T. Kloenne, Samuel R. Rogers, Chi Hang Dominik Kwok, Mark C. Hardy, Michele S. Conroy, David Dye   +6 more
wiley   +1 more source

Understanding the Stochastic Nature of Process Parameter Development of Blown Powder Laser Beam Directed Energy Deposition Additive Manufacturing of Pure Molybdenum

Advanced Engineering Materials, EarlyView.
Identified through the use of statistical design of experiments and metallographic investigation, this study exposes the stochastic origins of intergranular cracks in blown powder laser beam directed energy deposition additive manufacturing of pure molybdenum. It further demonstrates a successful crack mitigation approach with direct correlation to the
Nathaniel J. Lies, Daniel E. Driemeyer, Aaron P. Stebner   +2 more
wiley   +1 more source

A Combined of Path Analysis-MCDM Approaches to Evaluation of Leagile Suppliers [PDF]

International Journal of Industrial Engineering and Production Research
This study aims to evaluate the traditional, lean and agility criteria that are effective in evaluating the performance of suppliers and ranking them with the combined approach Path Analysis (PA), SWARA (Stepwise Weight Assessment Ratio Analysis) and ...
Mehdi Ajalli, Narges Soleiman Ekhtiyari, Peyman Zandi   +2 more
doaj