Results 41 to 50 of about 288 (160)

Wear mechanisms of PcBN tools when machining AISI 316L

Ceramics International, 2021
This paper investigates the machinability of AISI 316L stainless steel without and with NMI treatment, when machined with three different PcBN tool grades: low cBN content (50% vol.), medium (65% vol.) and high (90% vol.). The NMI treatment consisted of resulfurized and Ca-treated steels with two different Si/Al ratio. The tool materials were evaluated
Henrik Persson, Filip Lenrick, Luiz Franca, Jan-Eric Ståhl, Volodymyr Bushlya   +4 more
openaire   +1 more source

Experimental Study on Wear Characteristics of PCBN Tool with Variable Chamfered Edge

Chinese Journal of Mechanical Engineering, 2019
Owing to heavy dynamic and thermal loads, PCBN tools are seriously worn during hard cutting, which largely constrains the improvement of their machining performance.
Tao Chen, Lixing Song, Suyan Li, Xianli Liu   +3 more
doaj   +1 more source

Review on cutting performance and wear mechanism of PCBN tools

Jin'gangshi yu moliao moju gongcheng, 2020
Polycrystalline cubic boron nitride (PCBN) tool is another kind of superhard tool after polycrystalline diamond tool. It is known as the green environmental protection tool in the 21st century for its unique advanced cutting methods such as turning ...
CUI Jinmeng, MENG Dezhong, WU Zhe, YUE Wen, WANG Chengbiao   +4 more
doaj  

Investigation on surface morphology and crystalline phase deformation of Al80Li5Mg5Zn5Cu5 high-entropy alloy by ultra-precision cutting

Materials & Design, 2020
The materials with high precision，easy machining and excellent micro-machinability are considered significant on the fabrication of precision components, the outstanding comprehensive properties of Al80Li5Mg5Zn5Cu5 high-entropy alloy just meet these ...
Zhiyuan Huang, Yuqi Dai, Zhen Li, Guoqing Zhang, Chuntao Chang, Jiang Ma   +5 more
doaj   +1 more source

Sustainable Prediction of Tool Life in Metal Cutting Processes Using Empirical and Mathematical Modeling Approaches

Advances in Materials Science and Engineering, Volume 2026, Issue 1, 2026.
Tool‐life prediction plays a vital role in improving machining efficiency, reducing production cost, and promoting sustainable manufacturing in metal cutting processes. This study presents an empirical and mathematical modeling approach for predicting tool life based on flank wear behavior under varying machining conditions.
Nagaraj P. B., Gururaj Lalagi, Lokesha K., Mallikarjuna Veerabhadrappa Bidari, Rajesh K., Jibitesh Kumar Panda, Mohammad Rezwan Habib   +6 more
wiley   +1 more source

A Comparative Study on Cutting Tool Performance in High-Speed Face-Milling of Hardened Tool Steels [PDF]

Archives of Metallurgy and Materials
In this study cutting speeds and tool life constants for seven different cutting tools are investigated while high-speed face milling of four different much used hardened tool steels.1.2379 and 1.2080 cold-work tool steels, 1.2344 hot-work tool steel and
Ali O. Er, E. Aslan
doaj   +1 more source

Influence of Niobium Addition on Microstructure and Machinability of High Chromium Cast Iron

Materials Research, 2021
High Chromium Cast Iron (HCCI) is mostly utilised in environments under severe abrasion and corrosion wear conditions, and research on this material with added niobium obtained positive results regarding wear resistance.
Anderson Edson da Silva, Ismael Nogueira Rabelo de Melo, Ivete Peixoto Pinheiro, Leonardo Roberto da Silva   +3 more
doaj   +1 more source

Effect of Ti3AlC2 content on microstructure and properties of PcBN materials

Jin'gangshi yu moliao moju gongcheng
The monolithic PcBN composite tool materials were prepared at 5.5 GPa and 1450 ℃ with different contents of Ti3AlC2 as the binder phase. The effects of different mass fractions of Ti3AlC2 on the phase composition, microstructure, and mechanical ...
Jinming MA, Changjiang XIAO, Hongjun TAO, Qunfei ZHANG, Lihui TANG, Jianfeng CAO, Yuan LI, Shijie ZHOU, Yulin TANG, Yachao CHEN, Zhengxin LI   +10 more
doaj   +1 more source

Performance of the cutting tool equipped with PcBN of the BL group for high-speed processing of hardened steel

Технічна інженерія, 2023
The paper investigates PcBN cutting tools of the BL group developed at the Institute of Superhard Materials, made with the addition of ceramic components TaN, TiC, TiN. Such materials are classified as ceramic-matrix composites (CMC). The hardness of the
A.O. , Yu.O. , S.A. , A.S. , S.An., M.Yu. , O.S. , A.G. , L.G. , Y.P.   +9 more
doaj   +1 more source

Current Trends and Future Perspective for Cold Spray Metal‐Ceramic Composites

Advanced Engineering Materials, Volume 27, Issue 10, May 2025.
The use of cold spray (CS) technology for creating cermet deposits, combining ceramic and metallic components, is advancing rapidly. Cermets offer excellent temperature handling and erosion resistance for diverse applications. This review outlines the current state of the art, focusing on the deposition dynamics and strategies to optimize the ...
Romario A. Wicaksono, Amir Ardeshiri Lordejani, Sara Bagherifard   +2 more
wiley   +1 more source