Results 61 to 70 of about 3,382 (258)
Influence of Niobium Addition on Microstructure and Machinability of High Chromium Cast Iron
Materials Research, 2021 High Chromium Cast Iron (HCCI) is mostly utilised in environments under severe abrasion and corrosion wear conditions, and research on this material with added niobium obtained positive results regarding wear resistance.
Anderson Edson da Silva +3 more
doaj +1 more source
Surface Integrity of AISI 52100 Steel during Hard Turning in Different Near‐Dry Environments
Advances in Materials Science and Engineering, Volume 2020, Issue 1, 2020., 2020 AISI 52100 hardened bearing steel is popular in many industrial applications due to its excellent wear resistance and high strength. Therefore, a high level of surface integrity of the same is the utmost important requirement to enhance fatigue life. Machining of hardened AISI 52100 steel is difficult because severe plastic deformation and generation ...
Ajay Chavan +2 more
wiley +1 more source
Materials & Design, 2020 The materials with high precision，easy machining and excellent micro-machinability are considered significant on the fabrication of precision components, the outstanding comprehensive properties of Al80Li5Mg5Zn5Cu5 high-entropy alloy just meet these ...
Zhiyuan Huang +5 more
doaj +1 more source
Технічна інженерія, 2023 The paper investigates PcBN cutting tools of the BL group developed at the Institute of Superhard Materials, made with the addition of ceramic components TaN, TiC, TiN. Such materials are classified as ceramic-matrix composites (CMC). The hardness of the
A.O. +9 more
doaj +1 more source
Turning hardened steel using coated carbide at high cutting speeds [PDF]
, 2008 The present work studies some aspects of the turning process applied on hardened steel using multilayer coated carbide tools at high cutting speeds. The influence of cutting parameters (vc, f, and depth of cut - d.o.c.) on tool temperature, tool wear ...
ANEIRO, Federico M. +2 more
core +1 more source
A Comparative Study on Cutting Tool Performance in High-Speed Face-Milling of Hardened Tool Steels [PDF]
Archives of Metallurgy and MaterialsIn this study cutting speeds and tool life constants for seven different cutting tools are investigated while high-speed face milling of four different much used hardened tool steels.1.2379 and 1.2080 cold-work tool steels, 1.2344 hot-work tool steel and
Ali O. Er, E. Aslan
doaj +1 more source
Machines, 2022 Pulse laser grinding (PLG), as a cutting tool processing method, can not only achieve edge sharpening with high precision, but it can also produce surface modification.
Xiaoxu Liu +5 more
doaj +1 more source
Modelling of friction stir welding of DH36 steel [PDF]
, 2017 A 3-D computational fluid dynamics (CFD) model was developed to simulate the friction stir welding of 6-mm plates of DH36 steel in an Eulerian steady-state framework. The viscosity of steel plate was represented as a non- Newtonian fluid using a flow
A Arora +35 more
core +1 more source
Wear mechanisms of PcBN tools when machining AISI 316L
Ceramics International, 2021 This paper investigates the machinability of AISI 316L stainless steel without and with NMI treatment, when machined with three different PcBN tool grades: low cBN content (50% vol.), medium (65% vol.) and high (90% vol.). The NMI treatment consisted of resulfurized and Ca-treated steels with two different Si/Al ratio. The tool materials were evaluated
Henrik Persson +4 more
openaire +1 more source
A response surface methodology and desirability approach for predictive modeling and optimization of cutting temperature in machining hardened steel [PDF]
, 2014 This paper presents an experimental investigation on cutting temperature during hard turning of EN 24 steel (50 HRC) using TiN coated carbide insert under dry environment.
Ashok Kumar Sahoo, Purna Chandra Mishra
core +1 more source