Results 191 to 200 of about 1,566,640 (302)

Investigation of Thermo‐Chemical Processes in Commercial MgO‐C Refractory Bricks With and Without MgO‐C Recyclate at Elevated Temperatures

Advanced Engineering Materials, EarlyView.
This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm, Jana Hubálková, Christian Schimpf, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +6 more
wiley   +1 more source

Reliability and Validity of the Strain Gauge "GSTRENGTH" for Measuring Peak Force in the Isometric Belt Squat at Different Joint Angles. [PDF]

Sensors (Basel)
Varela-Olalla D, Balsalobre-Fernández C, Romero-Moraleda B, Jiménez-Sáiz SL.   +3 more
europepmc   +1 more source

Nanoscale simultaneous chemical and mechanical imaging via peak force infrared microscopy. [PDF]

Sci Adv, 2017
Wang L, Wang H, Wagner M, Yan Y, Jakob DS, Xu XG.   +5 more
europepmc   +1 more source

Engineered Mycelial Scaffolds With Tunable Ultraviolet Protection, Wettability, Thermal Stability, and Spatial Mechanics

Advanced Engineering Materials, EarlyView.
Fungal mycelia grown into biodegradable scaffolds and infused with titania nanoparticles show enhanced ultraviolet shielding, thermal protection, and surface nonwettability. Properties were tuned by drying methods, revealing structure–function relationships.
Juwon S. Afolayan, Xin Zhang, Carole C. Perry   +2 more
wiley   +1 more source

Peak Wind Force Coefficients for Balcony Handrail

Wind Engineers, JAWE, 2011
Kazuo OHTAKE, Osamu NAKAMURA, Yasuo OKUDA   +2 more
openaire   +2 more sources

Changes in isometric mid-thigh pull peak force and symmetry across anterior cruciate ligament reconstruction rehabilitation phases. [PDF]

Front Rehabil Sci
Stofberg JPJ, Aginsky K, van Aswegen M, Kramer M.   +3 more
europepmc   +1 more source

Correlation of Surface Morphology and Interfacial Adhesive Behavior between Cellulose Surfaces: Quantitative Measurements in Peak-Force Mode with the Colloidal Probe Technique. [PDF]

Langmuir, 2019
Lai Y, Zhang H, Sugano Y, Xie H, Kallio P, Kallio P.   +5 more
europepmc   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

Tomographic and multimodal scattering-type scanning near-field optical microscopy with peak force tapping mode. [PDF]

Nat Commun, 2018
Wang H, Wang L, Jakob DS, Xu XG.
europepmc   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source