Results 111 to 120 of about 44,113 (284)

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Seismic Fragility Analysis of RC Frames Under Near-Field and Far-field Ground Motion Based on Spectral Matching

工程科学与技术, 2018
Choosing the appropriate ground motion as input is the basis of nonlinear dynamic analysis and incremental dynamic analysis of structures.Firstly,20 suites of near-field ground motion records and 20 suites of far-field ground motion records were chosen ...
Jianping HAN, Shilong WEI, Xin ZHANG
doaj  

Effects of run-up velocity on performance, kinematics, and energy exchanges in the pole vault

, 2012
Copyright @ 2012 The Authors. This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and 85 reproduction in any medium, provided the original author and source
Linthorne, NP, Weetman, AHG
core  

Experimental Characterization of Mycelium‐Based Composites Under Multiple Loading Conditions

Advanced Engineering Materials, EarlyView.
This study examines the mechanical response of mycelium‐based composites under compression, shear, and tension using mechanical testing and imaging methods. The comparison between unpressed and hot‐pressed specimens shows that hot pressing is associated with higher compression and shear stiffnesses.
Shaghayegh Elahi, Kimiya Tajik, Harvey Shaw, Matti Isakov, Sami Pajunen, Lauri Rautkari   +5 more
wiley   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Laser‐Induced Graphene from Waste Almond Shells

Advanced Functional Materials, EarlyView.
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova, Anna Chiara Bressi, Marina Galliani, Attilio Marino, Gianni Ciofani, Eduardo Machado‐Charry, Hilda Gomez Bernal, Alessandra Francini, Luca Sebastiani, Francesco Greco   +9 more
wiley   +1 more source

Seismic hazard prediction of the Hunhe Fault in the Shen-Fu New District

Scientific Reports
Earthquake prevention and disaster mitigation are crucial aspects of social welfare that significantly impact national public security. This paper presents a seismic risk assessment and hazard prediction of the Hunhe Fault in the Shengyang-Fushun (Shen ...
Zijun Wang, Boming Zhao, Bo Wan
doaj   +1 more source

Biomass Native Structure Into Functional Carbon‐Based Catalysts for Fenton‐Like Reactions

Advanced Functional Materials, EarlyView.
This study indicates that eight biomasses with 2D flaky and 1D acicular structures influence surface O types, morphology, defects, N doping, sp2 C, and Co nanoparticles loading in three series of carbon, N‐doped carbon, and cobalt/graphitic carbon. This work identifies how these structural factors impact catalytic pathways, enhancing selective electron
Wenjie Tian, Jingkai Lin, Zhihao Tian, Selusiwe Ncube, Huayang Zhang, Emiliano Cortés, Hongqi Sun, Shaobin Wang   +7 more
wiley   +1 more source