Results 91 to 100 of about 3,231,468 (274)
Advanced Engineering Materials, EarlyView.Binder‐free laser powder bed fusion of 8YSZ with a femtosecond laser is used to map process windows linking scan strategy, heat accumulation, and grain growth. Time‐resolved thermography and simulations reveal thermal regimes that enable continuous, vitrified, and fine‐grained 8YSZ surface layers without absorptive additives and demonstrate ...
Markus Kühn +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.CT‐based finite element simulations combined with in situ X‐ray computed tomography are used to analyze insert pull‐out in nickel‐coated polymer foams. Despite variations in material parameters, deformation consistently concentrates within a narrow annular region around the insert.
Yannik Bautz +4 more
wiley +1 more source
Earth, Planets and SpaceThe 2024 Mw 7.5 Noto Peninsula earthquake was the largest inland earthquake recorded by dense K-NET and KiK-net strong-motion seismographs in Japan after their establishment in the second half of the 1990s.
Yadab P. Dhakal +6 more
doaj +1 more source
Design of a Multistable Finger Prosthesis with Programmable Metamaterials
Advanced Engineering Materials, EarlyView.This research article shows the development of a multistable programmble metamaterial for the use as a finger prosthesis. The material was designed on different hierarchical levels where the influence of geometrical parameters and combination of mechanical elements was explored.
Franziska Wenz +5 more
wiley +1 more source
Seismic dynamic response analysis for tunnels considering coseismic displacement
Yantu gongcheng xuebaoFault dislocation is a form of dynamic impact load that induces permanent deformation of the stratum in the vicinity of the fault. Based on the finite-fault source and crustal velocity model, coseismic displacement is computed according to the layered ...
FENG Jun1, 2 , ZHAO Boming1, 2 , WANG Zijun1, 2
doaj +1 more source
Investigation of Ground Vibration of Full-Stone Foundation under Dynamic Compaction
Shock and Vibration, 2019 This study focuses on the ground vibration of a full-stone foundation treatment project. The single-point dynamic compaction test was performed using a tamping machine at an energy level of 3200 kN·m. Time-history curves of ground vibration velocity were
Jiawen Wu +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji +3 more
wiley +1 more source
Peak ground velocity from dense seismic array in southern California
, 2020 The study explores the variability in peak ground velocity for >1000 nodal seismometers located in a small area on an active fault. The PGV values are derived from the 30 waveform trace for the station listed in the ZG network deployed from 07 May ...
Johnson, C (via Mendeley Data)
core +1 more source
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source
Advanced Engineering Materials, EarlyView.Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová +6 more
wiley +1 more source