Results 131 to 140 of about 21,537 (304)

Measurement of complex permittivity of composite materials using waveguide method [PDF]

, 2011
Complex dielectric permittivity of 4 different composite materials has been measured using the transmissionline method. A waveguide fixture in L, S, C and X band was used for the measurements.
Leferink, Frank Bernardus Johannes, Buesink, Frederik Johannes Karel, Leferink, Frank Bernardus Johannes; id_orcid, Tereshchenko, O.V.   +3 more
core  

Ti3C2Tx MXene/Silver Composite Foams For Lightweight, High‐Performance Electromagnetic Interference Shielding and Joule Heating

Advanced Materials Interfaces, EarlyView.
Ultrathin MXene/EMF composite foams achieve a specific shielding efficiency of 749.6 dB.dB·cm3$\mathrm{dB}\cdot {\mathrm{cm}}^{3}$/g, while the silver‐enhanced MXene/Ag/EMF reaches 81.4 dB shielding effectiveness at just 1.0 mm thickness. Both composites exhibit rapid Joule heating, retain stability up to 250∘C$^\circ{\rm C}$, and withstand 1000 ...
Abdullah A. Mahmood, Mingxuan Li, Vahid Rad, Mehdi Zarei, Chen‐Yu Yeh, Masoud Soroush, Guangyong Li, Paul W. Leu   +7 more
wiley   +1 more source

Dielectric permittivity extraction of MoS2 nanoribbons using THz nanoscopy

Nanophotonics
The nanoscale optical properties of high-quality MoS2 nanoribbons are investigated using THz nanoscopy based on a scattering-type scanning probe. The nanoribbons comprise a multilayer core, surrounded by monolayer edges.
Lassen Henrik B., Carstensen William V., Miakota Denys I., Ghimire Ganesh, Canulescu Stela, Jepsen Peter U., Kelleher Edmund J. R.   +6 more
doaj   +1 more source

Multifunctional Hollow Dielectric Resonator Design for Conductivity/Permittivity Measurements of Bulk Samples

, 2017
A hollow dielectric resonator has been developed for the measurement of either the conductivity or the permittivity of bulk samples in form of small cylinders.
Kostiantyn Torokhtii, Nicola Pompeo, Enrico Silva   +2 more
core  

Interfacial Electronic Restructuring in MAPbBr3/rGO Hybrids Enabling Improved Charge Extraction for Efficient Photodetection

Advanced Materials Interfaces, EarlyView.
MAPbBr3/rGO hybrids exhibit interfacial electronic restructuring that enhances charge extraction in photodetectors. The incorporation of rGO modifies the surface chemical environment, enhances electron‐dominated transport, and suppresses performance degradation, resulting in higher responsivity, detectivity, and photostability than in pristine MAPbBr3 ...
Mohammed Misbah Uddin, Wisnu Tantyo Hadmojo, Zeyad M. Abdulhamid, Marwa Abd‐Ellah, Ahmed L. Abdelhady   +4 more
wiley   +1 more source

Permittivity measurement of materials by coax probe

, 2015
This thesis describes possibilities of measuring permittivity of various materials, especially with coaxial probe method. It describes character of measuring method, hardware requirements and how to calculate values from the measured.
Ryba, Ivan
core  

Light Switchable Ionic Conductivity of Arylazopyrazole Modified Polysiloxanes

Advanced Materials Technologies, EarlyView.
We present a polysiloxane functionalized with a novel arylazopyrazole dye that undergoes reversible photoisomerization. Upon lithium bis(trifluoromethanesulfonyl)imide addition and UV irradiation, the polymer exhibits a shift in tan(d) toward higher frequencies and enhanced ionic conductivity.
Malte S. Beccard, Thulasinath Raman Venkatesan, Michael Bauer, Valentin Razvan Lupu, Philipp Scheidegger, Francesco Taddei, Frank A. Nüesch, Dorina M. Opris   +7 more
wiley   +1 more source

End‐to‐End Sensing Systems for Breast Cancer: From Wearables for Early Detection to Lab‐Based Diagnosis Chips

Advanced Materials Technologies, EarlyView.
This review explores advances in wearable and lab‐on‐chip technologies for breast cancer detection. Covering tactile, thermal, ultrasound, microwave, electrical impedance tomography, electrochemical, microelectromechanical, and optical systems, it highlights innovations in flexible electronics, nanomaterials, and machine learning.
Neshika Wijewardhane, Lyn I. Jones, Richard M. Martin, Helen Winter, Faezeh Arab Hassani   +4 more
wiley   +1 more source

Additively Manufactured Porous Ceramics as Tunable Dielectrics for Passive Temperature Sensing

Advanced Materials Technologies, EarlyView.
Porous ceramic lattices, 3D‐printed from a multicomponent oxide ink, are integrated with LC resonators for passive wireless temperature sensing. By tuning porosity, the dielectric properties and RF response are engineered to produce distinct resonant frequency shifts with temperature. The results establish a structure‐driven approach to customizing the
Sogol Heidarishahrivar, Aminul Islam, Chang Woo Gal, Insup Kim, Yeong‐Jin Choi, Woo Soo Kim   +5 more
wiley   +1 more source