Results 71 to 80 of about 6,631 (213)

Valorization of recycled fine powder glass (RFPG) in additive manufacturing: Optimization of the RFPG content in polyethylene terephthalate glycol (PETG) and multi-response analysis

Cleaner Materials
A cyclic economy and sustainability-driven production are key aspects of the industry. Recycled feedstocks are steadily replacing virgin materials to produce parts and as sustainable additives to develop eco-friendly composites. The reinforcing potential
Markos Petousis, Nikolaos Michailidis, Václav Kulas, Vassilis Papadakis, Mariza Spiridaki, Nikolaos Mountakis, Apostolos Argyros, John Valsamos, Emmanouel Stratakis, Nectarios Vidakis   +9 more
doaj   +1 more source

Optimizing Charpy Impact Strength of Material‐Extruded PLA Through Layer Height, Raster Angle, and Infill Geometry

Journal of Applied Polymer Science, EarlyView.
Charpy impact performance of material‐extruded PLA is governed by the coupled effects of layer height, raster angle, and infill geometry. Full‐factorial testing identifies layer height as the dominant factor and reveals a strong layer‐height–raster‐angle interaction.
Yazan Mashaki, Luis Hoi Fan, Shafahat Ali, Salman Pervaiz, Ibrahim Deiab   +4 more
wiley   +1 more source

Evaluation of thermoplastic composites for the manufacture of H-Darrieus wind Turbine blades on a laboratory scale

Journal of Materials Research and Technology
Wind energy is one of the most widely produced sources of renewable and clean electricity. However, the blades of wind turbines pose a significant environmental challenge due to the difficulty in recycling them. To address this issue, research is focused
Andres F. Olivera, Edwin L. Chica, Henry A. Colorado   +2 more
doaj   +1 more source

A Fast B1+$$ {B}_1^{+} $$‐Driven RF Co‐Simulation Optimization Method for RF Coil Arrays

Magnetic Resonance in Medicine, EarlyView.
ABSTRACT Purpose To generate accurate EM simulation models of RF coil arrays, improve coil safety validation procedures, and improve RF power management without sacrificing patient safety. Methods A fast, customized RF co‐simulation formulation was developed for pTx RF coils, enabling the use of experimentally measured B1+$$ {B}_1^{+} $$ maps to ...
Mazin M. Mustafa, Ethan Polcyn, Matt Waks, Alexander Bratch, Gregory J. Metzger, Xiufeng Li, Yigitcan Eryaman   +6 more
wiley   +1 more source

Combined Effects of Thermal Cycling Aging and Reinforcement Content on the Ball‐On‐Disk Wear of Additively Manufactured Polylactic Acid Composites

Polymer Composites, EarlyView.
Thermal Aging and Tribological Tests of Additive Manufactured PLA Composites. ABSTRACT This study focuses on the additive manufacturing of pure polylactic acid (PLA) specimens and milled glass fiber (GF)‐filled PLA composites under thermal cycling aging and wear tests. Wear tracks have been analyzed via 3D optical profiling and SEM imaging.
Sinan Fidan, Satılmış Ürgün, Nevin Gamze Karsli, Taner Yilmaz, Mustafa Özgür Bora, Mehmet İskender Özsoy   +5 more
wiley   +1 more source

Additive Manufacturing of Glass Fiber‐Reinforced Polypropylene and Its Behavior Under Controlled Hydrogen Exposure

Polymer Composites, EarlyView.
Experimental and numerical assessment of GFRPP under lower experimental hydrogen pressures using tensile testing, SEM analysis, and hydrogen uptake estimation. ABSTRACT Glass fiber‐reinforced polypropylene (GFRPP) composites are increasingly explored for hydrogen transport and storage due to their lightweight nature and corrosion resistance.
Ahmadyar Qureshi, Ulises Martin, Abdul Mannan, Homero Castaneda   +3 more
wiley   +1 more source

Mechanical and Impact Response of Adhesively Bonded ASA/PA12 Sandwich Structures Produced by Fused Filament Fabrication

Polymer Engineering &Science, EarlyView.
Adhesively bonded ASA/PA12 FFF sandwich structures reveal that interfacial compliance governs mechanical performance. Cyanoacrylate enhances strength but induces brittle failure, while polyurethane improves ductility and impact resistance, demonstrating that adhesive properties and stacking sequence are critical design parameters for optimizing multi ...
Berkay Ergene, Bayram Yildiz, Tolgahan Ermergen, Çağın Bolat   +3 more
wiley   +1 more source

Effect of Coupling Agent on the Dispersion of PETG Montmorillonite Nanocomposite films.

, 2003
Polyethylene terephthalate glycol (PETG) is a clear amorphous polymer, which is extensively used in flexible packaging. The dual packaging requirements of recyclability and long-term shelf life are often difficult to achieve.
Nandika D'Souza, Christopher Thellen, Bruce Gnade, Caitlin Orroth, Danielle Froio, Jo Ann Ratto, Ajit Ranade, Jeanne Lucciarini   +7 more
core   +1 more source

3D printed polyethylene terephthalate glycol ternary composites with short carbon fiber/ carbon nanotube graphitic reinforcements: Insights into multi-scale synergistic mechanisms

Composites Part C: Open Access
Three-dimensional printed (3DP) Polyethylene Terephthalate Glycol (PETG) ternary composites reinforced with short carbon fibers (sCF) and multi-walled carbon nanotubes (CNT) are reported for the first time. A single-screw extrusion process is employed to
Fivos Simopoulos, George Kampourakis, George Karalis, Benke Li, Emmanouil Porfyrakis, Stavros Katsiaounis, Aaron Soul, Dimitrios Papageorgiou, Marco Liebscher, Konstantinos Papagelis, Apostolos Karanastasis, Nikolaos Papadakis, Lazaros Tzounis   +12 more
doaj   +1 more source

Effects of Annealing on the Thermomechanical Properties and Crystallization Behavior of FDM‐Printed High‐Temperature PLA and Glass Fiber PLA Composites

Polymer Engineering &Science, EarlyView.
Overview of the study evaluating the impact of post‐print annealing on the microstructural crystallization and thermomechanical properties of FDM‐printed high‐temperature PLA and glass fiber‐reinforced PLA composites. ABSTRACT Polylactic acid (PLA) combines renewable sourcing and reliable printability with limited stiffness retention near its glass ...
Huseyin Erdem Yalkin, Ayse Nur Ozkan
wiley   +1 more source