Results 31 to 40 of about 6,230,450 (205)

Mechanical Characterization of PETG/TPU Multi-Material 3D-Printed Samples and Fabrication of a Test Part

open access: yesEngineering Proceedings
The present article aims to explore the feasibility of manufacturing multi-material components from PETG and TPU using FFF/FDM 3D printing. The mechanical characterization includes Shore hardness measurements of the individual materials and Izod impact ...
Mihail Zagorski   +3 more
doaj   +1 more source

Avaliação do PETG como material para imobilizadores utilizados em radioterapia para cabeça e pescoço

open access: yesBrazilian Journal of Radiation Sciences, 2020
No planejamento do tratamento radioterápico do câncer de cabeça e pescoço, o radioncologista pode indicar o uso de uma prótese intraoral para facilitar a técnica de radioterapia e reduzir a toxicidade do tratamento.
Heitor Ribeiro Birnfeld   +4 more
doaj   +1 more source

Modal response of hybrid raster orientation on material extrusion printed acrylonitrile butadiene styrene and polyethylene terephthalate glycol under thermo-mechanical loads

open access: yesPolymer Testing, 2023
In this paper we look at Acrylonitrile Butadiene Styrene (ABS) and Polyethylene Terephthalate Glycol (PETG), chosen for their low cost, high strength and temperature resistance.
Mohammed Dukhi Almutairi   +4 more
doaj   +1 more source

Experimental characterization of the mechanical properties of PETG and PA6 thermoplastics

open access: yes, 2018
Simple thermoplastic materials and polymer matrix composites have been used in this work. Polyethylene terephthalate glycol (PETG) plates, a copolymer of CHDM- cyclohexane dimethanol modified polyethylene terephthalate [56], were used, which is an ...
Coba Salcedo, Milton Fabian   +5 more
core   +1 more source

Evaluation of thermoplastic composites for the manufacture of H-Darrieus wind Turbine blades on a laboratory scale

open access: yesJournal of Materials Research and Technology
Wind energy is one of the most widely produced sources of renewable and clean electricity. However, the blades of wind turbines pose a significant environmental challenge due to the difficulty in recycling them. To address this issue, research is focused
Andres F. Olivera   +2 more
doaj   +1 more source

Fused Filament Fabrication Additive Manufacturing: Mechanical Response of Polyethylene Terephthalate Glycol

open access: yesAnnals of "Dunarea de Jos" University of Galati, Fascicle XII, Welding Equipment and Technology, 2021
The additive manufacturing (AM) fused filament fabrication (FFF) technology is widely used today with different kinds of thermoplastic materials, including polyethylene terephthalate glycol (PETG).
O. Kohn   +4 more
doaj   +1 more source

Constituent-Material-Anchored Continual Learning for Full Stress-Strain Prediction of Multi-Material PETG/PC-ABS MEX Laminates. [PDF]

open access: yesPolymers (Basel)
Predicting the tensile response of multi-material parts produced by material extrusion (MEX) remains difficult because the final behavior depends on both the constituent polymers and the quality and arrangement of dissimilar interfaces. This study introduces a constituent-material-anchored, phase-aware continual-learning framework for full stress ...
Subramanian RA   +5 more
europepmc   +3 more sources

A Soft Robotic Fish With a Dielectric Elastomer Actuator Body and Negative Stiffness Spine

open access: yesAdvanced Robotics Research, EarlyView.
This work introduces a bio‐mimetic soft robotic fish driven by fiber‐reinforced dielectric elastomer actuators integrated as its body. By prestretching this active skin against a flexible spine, a negative stiffness system is created, enabling large‐amplitude bending.
Markus Koenigsdorff   +4 more
wiley   +1 more source

Stiffness‐Programmable Origami Robots With Tendon‐Driven Actuation via Multimaterial 3D Printing

open access: yesAdvanced Robotics Research, EarlyView.
Motion diversity is achieved in a tendon‐driven origami robot through programmable stiffness rather than modified actuation. Multimaterial 3D printing embeds soft creases, modular inserts redirect identical tendon inputs into distinct behaviors, and variable‐stiffness inserts enable real‐time switching.
Elisha Lerner, Jianguo Zhao
wiley   +1 more source

WorMa: An Undulatory Robot With Center of Mass Regulation via Internal Fluid Redistribution for Amphibious Locomotion

open access: yesAdvanced Robotics Research, EarlyView.
WorMa is an amphibious undulatory robot that uses Center of Mass redistribution as the sole terrain adaptation mechanism. This mechanism is based on internal fluid mass redistribution through a pump‐driven latex balloon system that creates three profiles: head‐biased, balanced, and tail‐biased.
Daniil Filimonov, Nana Obayashi
wiley   +1 more source

Home - About - Disclaimer - Privacy