Results 151 to 160 of about 1,908,179 (350)

Microstructural Evolution and Mechanical Performance of Plasma‐Assisted Hybrid Friction Stir Welded Dissimilar Aluminum–Copper Joints

Advanced Engineering Materials, EarlyView.
Plasma‐assisted hybrid friction stir welding of dissimilar AlCu joints employs localized plasma preheating to balance heat input and enhance plastic flow. The optimized process reduces axial force by up to 35%, refines the microstructure, and achieves ≈96% joint efficiency.
Deepak Kumar Yaduwanshi, Pankaj Shrivastava, Ganesh Chouhan, Velaphi Msomi   +3 more
wiley   +1 more source

Determination of contact angles for three-phase flow in porous media using an energy balance

, 2020
Martin J. Blunt, Abdulla Alhosani, Qingyang Lin, Alessio Scanziani, Branko Bijeljic   +4 more
openalex   +2 more sources

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Response of hot element flush wall gauges in oscillating laminar flow [PDF]

The time dependent response characteristics of flush-mounted hot element gauges used as instruments to measure wall shear stress in unsteady periodic air flows were investigated.
Cook, W. J., Giddings, T. A.
core   +1 more source

The effect of contact angle hysteresis on a droplet in a viscoelastic two-phase system [PDF]

Kazem Bazesefidpar, Outi Tammisola
openalex   +1 more source

The diagnostic value of phase angle, an integrative bioelectrical marker, for identifying individuals with dysmobility syndrome: the Korean Urban-Rural Elderly study

, 2020
Yeon Woo Jung, Namki Hong, Chang Oh Kim, Hyeon Chang Kim, Yousik Youm, Jin‐Young Choi, Yumie Rhee   +6 more
openalex   +2 more sources

An international comparison of phase angle standards between the novel impedance bridges of CMI, INRIM and METAS [PDF]

, 2018
Massimo Ortolano, L. Palafox, Jan Kučera, Luca Callegaro, Vincenzo D’Elia, Martina Marzano, F. Overney, Gülay Gülmez   +7 more
openalex   +1 more source

The clinical application value of phase angle of six parts in nutritional evaluation of tumor patients [PDF]

, 2022
Xiaoling Zhang, Jialei Zhang, Yunyi Du, Xiaoyu Wu, Yali Chang, Weiling Li, Yaqin Liu, Wenqing Hu, Jun Zhao   +8 more
openalex   +1 more source

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source