Results 181 to 190 of about 886 (213)

Effect of hydrodynamics and mass transfer processes on biomass production of Synechococcus HS-9 cultivated using rectangular airlift photobioreactors with baffles. [PDF]

Sci Rep
Rahman A, Prihantini NB, Oktaufik MAM, Irwansyah R, Kholiq MA, Levison AK, Rahadiyan L, Aziz M, Wahyono Y, Ariyanti D, Nasruddin N.   +10 more
europepmc   +1 more source

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source

An Experimental High‐Throughput Approach for the Screening of Hard Magnet Materials

Advanced Engineering Materials, EarlyView.
An entire workflow for the high‐throughput characterization and analysis of compositionally graded magnetic films is presented. Characterization protocols, data management tools and data analysis approaches are illustrated with test case Sm(Fe, V)12 based films.
William Rigaut, Pierre Le Berre, Hamdi Jaballah, Lukas Fink, Victor Poline, Richard Haettel, Stéphane Grenier, Gilbert Chahine, Ewen Bellec, Guillaume Buatier, Wilfried Hortschitz, Santa Pile, Thomas Schrefl, Nils Blanc, Yuan Hong, Thibaut Devillers, Nora M. Dempsey   +16 more
wiley   +1 more source

Hydrodynamic features of pulsed solvent extractor for separation of two metals by using the antagonistic effect of solvents. [PDF]

Sci Rep
Asadollahzadeh M, Torkaman R.
europepmc   +1 more source

Influence of Surface Finish on the Tribological Performance of AlTiBN Coatings Deposited on Forming Tools

Advanced Engineering Materials, EarlyView.
Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver, Iker Alfonso, Eneko Barba, Javier León, José Antonio García, Iñaki Zalakain, Iván Fernández Martínez, Arley García‐Carrero, Christian Almeyda, Daniel Salcedo   +9 more
wiley   +1 more source

Modular and Cost-Effective Computed Tomography Design. [PDF]

Sensors (Basel)
Bieberle A, Hoffmann R, Döß A, Schleicher E, Hampel U.   +4 more
europepmc   +1 more source

Low Cycle Repetitive Loading of Ti‐6Al‐4V‐Epoxy Composite Lattice Structures for Enhanced Energy Dissipation and Damage Tolerance

Advanced Engineering Materials, EarlyView.
Composite Ti–6Al–4V–epoxy lattice structures are additively manufactured and epoxy infiltrated for cyclic loading. At low lattice volume fractions, hybridization produces synergistic gains in stiffness and energy dissipation. At higher volume fractions, synergy diminishes, although composites still exceed metallic lattices in specific energy ...
Joey Tallon, Jordan Noronha, Justin Dirrenberger, Andrey Molotnikov   +3 more
wiley   +1 more source

Mitigating Liquid Loading in Gas Wells Using Thermochemical Fluid Injection: An Experimental and Simulation Study. [PDF]

ACS Omega
Elyasa A, Hassan A, Mahmoud M, Gajbhiye R, El-Husseiny A, Abu-Mahfouz IS.   +5 more
europepmc   +1 more source

Impact of thermodynamics and kinetics on the carbon capture performance of the amine-based CO₂ capture system. [PDF]

Environ Sci Pollut Res Int
Kopac T, Demirel Y.
europepmc   +1 more source