Results 171 to 180 of about 338,499 (317)
Advanced Engineering Materials, EarlyView.A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
An instantaneous frequency-based computation of transparent motion [PDF]
We extend the principle of phase-based techniques for measuring optical flow and binocular disparity to multiple motion estimation. Using quadrature filter pairs, we estimate phase gradients (instantaneous frequency) from independent bandpass channels ...
Atherton, T. J. +2 more
core
, 2014 Citation: 'reduced mobile phase velocity' in the IUPAC Compendium of Chemical Terminology, 3rd ed.; International Union of Pure and Applied Chemistry; 2006. Online version 3.0.1, 2019. 10.1351/goldbook.R05215 • License: The IUPAC Gold Book is licensed under Creative Commons Attribution-ShareAlike CC BY-SA 4.0 International for individual terms ...
openaire +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Guiding Optical Flow Estimation
, 2003 We show how optical flow estimates can be combined with boundary estimation to improve estimates of motion. The improvement is associated with blending of estimates from complementary bases of operation.
Myerscough, Peter J +2 more
core
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
, 2006 This paper presents an experimental study to investigate the suitability of thick-film ultrasonic transducers for composition measurements in heterogeneous mixtures. Following on from earlier developments [G. Meng, A.J. Jaworski, T. Dyakowski, J.M. Hale,
Jaworski, Artur +2 more
core
Two-Signal Set and Adaptive Spectral Decomposition Algorithm for Estimating the Phase Velocity of Dispersive Lamb Wave Mode. [PDF]
Sensors (Basel)Draudvilienė L +3 more
europepmc +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source