Results 101 to 110 of about 47,846 (307)
, 2010 The high efficiency limit of the intermediate band solar cell (IBSC) corresponds to the case of using as intermediate band (IB) host material a semiconductor with gap in the range of 2 eV.
García-Linares Fontes, Pablo +5 more
core
Advanced Materials, EarlyView.An Aloe‐pinspired droplet electricity generator (A‐DEG) overcomes the limited energy collection zone of conventional DEGs by guiding impact droplets through a channeling midrib and artificial cuticle. The channeling midrib induces uni‐directional droplet spreading, while the artificial cuticle on the midrib further reinforces this behavior through its ...
Gibeom Lee +8 more
wiley +1 more source
, 2014 Spintronics, which aims at exploiting the spin degree of freedom of carriers inside electronic devices, has a huge potential for quantum computation and dissipationless interconnects. Ideally, spin currents in spintronic devices should be powered by a spin voltage generator able to drive spins out of equilibrium and produce two spatially well-separated
Bottegoni, F. +6 more
openaire +2 more sources
Innovation and international technology transfer: The case of the Chinese photovoltaic industry [PDF]
China is the largest solar photovoltaic cell producer in the world, with more than one third of worldwide production in 2008, exporting more than 95 percent of what it produces.
Matthieu Glachant +2 more
core
Design of a GaInP/GaAs tandem solar cell for maximum daily, monthly, and yearly energy output
, 2011 Solar concentrator cells are typically designed for maximum efficiency under the AM1.5d standard spectrum. While this methodology does allow for a direct comparison of cells produced by various laboratories, it does not guarantee maximum daily, monthly ...
Haas, Alexander W. +3 more
core +1 more source
Cell-To-Module (CTM) Analysis for Photovoltaic Modules with Cell Overlap
, 2020 Both, the interconnection of solar cells by ribbons and shingling are known to the solar industry. Typically cells interconnected with ribbons did not overlap while modules with shingled cells did not feature ribbons.
Mittag, Max +2 more
core +1 more source
Leaftronics: Bio‐Fractal Scaffolds From Leaf Venation for Low‐Waste Electronics
Advanced Materials, EarlyView.“Leaftronics” transforms naturally evolved leaf venation into quasi‐fractal scaffolds for sustainable electronics. Polymer‐infiltrated leaf skeletons can be used to fabricate ultra‐smooth, reflow‐ and thin‐film‐compatible decomposable substrates, while making the same lignocellulose networks conducting results in flexible transparent electrodes.
Rakesh Rajendran Nair +3 more
wiley +1 more source
Thermal analysis of film photovoltaic cell subjected to dual laser beam irradiation
, 2015 The concept of dual laser beam irradiation was firstly demonstrated on the photovoltaic cell, of which the temperature dependent efficiency was investigated for wireless power transmission.
Wu CW(吴臣武) +2 more
core +1 more source
Rethinking Charge Transport and Recombination in Donor‐Diluted Organic Solar Cells
Advanced Materials, EarlyView.Organic solar cells with 1–45% PM6 content in Y12 were studied to link structure and charge dynamics to performance. The conductivity follows a 3D percolation model without a sharp threshold. Donor dilution preserves the photogeneration yield, but limits the fill factor due to transport resistance losses.
Chen Wang +14 more
wiley +1 more source
Advanced Materials, EarlyView.Mechanically origami‐coded 3D kirigami photovoltaics convert a single extension–release cycle into deterministic self‐folding, reconfiguring planar solar cells into programmable 3D modules. Distinct coding strategies enable either ultrahigh stretchability (500% system strain) or ultrahigh initial effective areal coverage (225%).
Seok Joon Hwang +15 more
wiley +1 more source