Results 171 to 180 of about 2,432,332 (208)

Development of a Solid‐Liquid Hybrid Electrolyte Composed of LiTa2PO8 and [C2mim][FSA]–Li[FSA] Ionic Liquid for Rechargeable Lithium Metal Batteries

open access: yesAdvanced Materials Interfaces, EarlyView.
LiTa2PO8 (LTPO) suffers from high interfacial resistance when paired with Li metal due to poor solid‐solid contact. Coating LTPO with an ionic liquid (IL) markedly improves interfacial stability, maintaining favorable resistance up to 2000 cycles. However, contact between IL‐coated LTPO and Li metal induces discoloration of LTPO, which is attributed to
Mizuki Fukuda   +5 more
wiley   +1 more source

Control of Bacterial Attachment on Macroporous PDMS/Paraffin SLIPS With Varying Lubricant Viscosity

open access: yesAdvanced Materials Interfaces, EarlyView.
Slippery liquid‐infused porous surfaces (SLIPS) prepared from macroporous PDMS, infused with medical‐grade paraffins, were systematically investigated regarding the correlation of viscosity, surface corrugation, bulk porosity, and bacterial resistance. Substrate porosity was found to dominate lubricant stabilization and the antifouling activity.
Regina Kopecz   +3 more
wiley   +1 more source

Wood‐Derived Nanocellulose‐Biocarbon Fresnel‐Zone Plate Lenses for Sub‐THz Frequency Applications

open access: yesAdvanced Materials Technologies, EarlyView.
Wood‐derived nanocellulose and lignin‐based biocarbon were combined to fabricate fully bio‐based Fresnel zone plate (FZP) lenses for sub‐terahertz frequencies. These sustainable FZP lenses exhibit low dielectric loss and high directivity, achieving performance comparable to that of metallic references, and remain functional under environmental stress ...
Riikka Haataja   +9 more
wiley   +1 more source

Programmable Variable‐Stiffness Multilayer Elastomer Composites With High‐Aspect‐Ratio Low‐Melting‐Point Alloy Inclusions

open access: yesAdvanced Materials Technologies, EarlyView.
High‐aspect‐ratio low‐melting‐point alloy inclusions are embedded within multilayer silicone laminates to create thermally programmable stiffness. Sequential activation of alloy‐rich layers produces four distinct mechanical states and reconfigures tendon‐driven actuator trajectories under the same load.
Palpolage Don Shehan Hiroshan Gunawardane   +4 more
wiley   +1 more source

In‐House Manufacturing of 3D ECM Culture Chips via Vacuum Thermoforming for Enhanced Imaging Applications

open access: yesAdvanced Materials Technologies, EarlyView.
Desktop vacuum thermoforming enables rapid, low‐cost fabrication of 96‐channel polystyrene culture chips with very thin imaging interfaces. The resulting platform supports cell lines, primary cells, and patient‐derived organoids, and enables high‐resolution confocal microscopy and single‐cell visualization, providing an accessible approach for advanced
Aleksandra Fomina   +5 more
wiley   +1 more source

Unlocking Terahertz Steganography: Authentication of Hidden Images in Flexible Media

open access: yesAdvanced Materials Technologies, EarlyView.
Hidden information in multilayered devices, such as steganographic portraits, is detected and authenticated using reflection‐mode terahertz time‐domain imaging. Image reconstruction relies on a dedicated figure‐of‐merit obtained by integrating the signal intensity over the time‐window associated with the reflection from the metallic mirror backing the ...
Tiziana Ritacco   +4 more
wiley   +1 more source

Exceptional Elasto‐Dielectric Properties in a Highly Flexible Dielectric Elastomer Composite: The Key Roles of Parallel Elastic Nanofibers

open access: yesAdvanced Materials Technologies, EarlyView.
Soft dielectric elastomer composites often face a trade‐off between enhanced dielectric properties and mechanical compliance. Here, a parallel‐aligned polyurethane nanofiber network embedded in PDMS creates a flexible, durable composite with increased permittivity, low modulus, and fatigue stability after 100,000 cycles.
Yi Ge   +9 more
wiley   +1 more source

Chitin‐Chitosan Cryogels for the Reversible Sequestration and Recovery of Heavy Metals From Wastewater

open access: yesAdvanced Materials Technologies, EarlyView.
Chitin‐chitosan cryogels with degrees of N‐acetylation from 12.2% to 71.4% are fabricated by dissolution, coagulation and lyophilization for the sequestration of heavy metals from water. Colorimetry and differential pulse voltammetry showed controlled adsorption and desorption capacities for As5+, Co2+ and Cu2+, making this material attractive for ...
Marta García‐Castrillo   +4 more
wiley   +1 more source

Region‐Specific Profiling of the Gut Microbiome and Metabolite Landscape in Response to Dietary Intervention Using Electronics‐Free Ingestible Smart Sampling Capsules

open access: yesAdvanced Materials Technologies, EarlyView.
Region‐specific profiling of the gut microbiome is achieved non‐invasively using electronics‐free ingestible sampling capsules that activate at defined intestinal sites through stimuli‐responsive coatings. Deployed in a porcine dietary intervention model, the capsules resolve spatially distinct, fiber‐driven shifts in microbial composition and short ...
Devendra Sarnaik   +8 more
wiley   +1 more source

Autonomous Reconfigurable Modular Conductive Hydrogels for Adaptive and Degradable Bioelectronic Interfaces

open access: yesAdvanced Materials Technologies, EarlyView.
Bridging rigid electrodes with soft, irregular tissues demands more than conductivity alone. Modular conductive hydrogels autonomously reconfigure into conformal electrode‐tissue interfaces, coupling mixed ionic‐electronic conduction with tissue‐like mechanics, self‐healing, and degradability.
Matthew K. Burgess   +4 more
wiley   +1 more source

Home - About - Disclaimer - Privacy