Results 81 to 90 of about 25,595 (290)
Advanced Science, EarlyView.Through a systematic and comprehensive analysis of the environmental impacts for the emerging MXene synthesis pathways, this study presents process transformation and optimization opportunities for low‐carbon MXene production from laboratory to industrial scales.
Yushuai Huang +6 more
wiley +1 more source
Исследование процесса окисления механоактивированных ультрадисперсных порошков железа [PDF]
, 2015 The oxidation of mechanically activated ultrafine iron powders was studied using X-ray powder diffractionand thermogravimetric analyzes. The powders with average particles size of 100 nm were made by the electricexplosion of wire, and were subjected to ...
Власов, Виталий Анатольевич +2 more
core
Advanced Science, EarlyView.Complex hydride anion substitution in argyrodite electrolytes has attracted attention for improving interfacial stability, yet the influence of these anions at Li metal interfaces remains unclear. This work shows that electrochemically formed BH4−‐derived interphases enable stable high‐current full‐cell cycling.
Sangho Lee +13 more
wiley +1 more source
BuildingsThis research used fly ash and slag to create geopolymer foam concrete. They were activated with an alkali, resulting in a chemical reaction that produced a gel that strengthened the concrete’s structural integrity.
Xuan Liu +5 more
doaj +1 more source
Advanced Science, EarlyView.CO2 significantly accelerates hydrogen release from aqueous NaBH4 without metal catalysts, eliminating the need for downstream separation. Ball‐milling the hydrolytic products with Mg regenerates NaBH4 with yields exceeding 76% while simultaneously producing methane.
Rui Han +8 more
wiley +1 more source
Effects of the speed ratio on the efficiency of planetary mills
Heliyon, 2019 The ignition time (tig) of the mechanically induced self-sustaining reaction (MSR) process involving the formation of TiB2 from Ti/2B elemental mixtures was used to study the influence of the ratio (k = -ωv/ωd) between the rotational speed of the ...
C. Real, F.J. Gotor
doaj +1 more source
Study of barium bismuth titanate prepared by mechanochemical synthesis [PDF]
, 2009 Barium-bismuth titanate, BaBi4Ti4O15 (BBT), a member of Aurivillius bismuth-based layer-structure perovskites, was prepared from stoichiometric amounts of barium titanate and bismuth titanate obtained via mechanochemical synthesis.
Bobić J. +4 more
core +1 more source
Ionic Elastomer Interface for Low‐Pressure and Durable All‐Solid‐State Batteries
Advanced Energy Materials, EarlyView.This work reports an ionically conductive elastomer that enables stable all‐solid‐state batteries（ASSBs）under low external pressure. The soft elastomeric matrix, integrated with a LiG3‐based conductive phase(lithium bis(trifluoromethanesulfonyl)imide and triethylene glycol dimethyl ether), simultaneously delivers high ionic conductivity and mechanical ...
Jiaxu Zhang +15 more
wiley +1 more source
Advances in Materials Science and Engineering, 2013 Multiwall carbon nanotubes (MWCNTs) reinforced Mg alloy AZ31 nanocomposites were fabricated by mechanical alloying and powder metallurgy technique. The reinforcement material MWCNTs were blended in three weight fractions (0.33%, 0.66%, and 1%) with the ...
J. Jayakumar, B. K. Raghunath, T. H. Rao
doaj +1 more source
Study of the formation of Cu-24at.% Al by reactive milling [PDF]
, 2015 In this work, powders of Cu and Al were milled with a proportion equal to 24 atomic % Al, using low and medium energy mills. The initial, intermediate and final stages of the resulting powder are analyzed using scanning electron microscopy, X-ray ...
Esquivel, Marcelo Ricardo Oscar +4 more
core +1 more source