Results 191 to 200 of about 34,157 (310)

Overcoming Printing and Interfacial Challenges in Liquid Metal Direct Writing for Integrated Stretchable Electronics

Advanced Materials Technologies, EarlyView.
Liquid metal direct writing is advanced from a technological and fundamental point. Utilizing a kinematic bed, printing on large surfaces with irregularities is enabled. Furthermore, a pressure‐driven flow during printing is discovered that affects the thickness of traces.
Maximilian Krack, Lennert Purnal, Parth Vinayakrao Sewlikar, Sam Cuyvers, Gus Geurts, Rathul Nengminza Sangma, Derese Desta, Dieter Reenaers, Bart Ruttens, Iris De Graeve, Tom Hauffman, Seppe Terryn, Bram Vanderborght, Michaël Daenen, Wim Deferme, Monika Rai   +15 more
wiley   +1 more source

The Impact of Pressure-Dependent Viscosity Data on Injection Molding Simulations of Highly Filled Thermoplastics. [PDF]

Polymers (Basel)
Kerling F, Schlicht S, Roth B, Kleffel T, Rösel U, Drummer D.   +5 more
europepmc   +1 more source

The latest technology in plastic injection molding [PDF]

, 2015
Antonov, Andrij, Nakonetchnj, Yurij, Yarema, Igor, Антонов, Андрій, Наконечний, Юрій Іванович, Ярема, Ігор Теодорович   +5 more
core  

End‐to‐End Sensing Systems for Breast Cancer: From Wearables for Early Detection to Lab‐Based Diagnosis Chips

Advanced Materials Technologies, EarlyView.
This review explores advances in wearable and lab‐on‐chip technologies for breast cancer detection. Covering tactile, thermal, ultrasound, microwave, electrical impedance tomography, electrochemical, microelectromechanical, and optical systems, it highlights innovations in flexible electronics, nanomaterials, and machine learning.
Neshika Wijewardhane, Lyn I. Jones, Richard M. Martin, Helen Winter, Faezeh Arab Hassani   +4 more
wiley   +1 more source

Impact of Replicated Biomimetic Microstructures on the Wettability of Injection-Molded Polymer Surfaces. [PDF]

Biomimetics (Basel)
Šorm V, Bittner J, Lenfeld P, Kroisová D, Dvořáčková Š.   +4 more
europepmc   +1 more source

Introduction to Plastic Injection Molds

Transactions of Materials Processing, 2002
openaire   +2 more sources

Flexible Chemiresistive Chitosan‐Glycerol Sensors on Laser‐Induced Graphene Electrodes for Room‐Temperature Ammonia Detection

Advanced Materials Technologies, EarlyView.
Flexible Chitosan‐glycerol sensor integrated with porous laser‐induced graphene (LIG) electrodes enable room‐temperature chemiresistive detection of ammonia (NH3) and proof‐of‐concept detection of fish spoilage. ABSTRACT We report a metal‐free sensor platform combining laser induced graphene (LIG) electrodes with drop‐deposited, glycerol‐plasticized ...
Mintesinot Tamiru Mengistu, Richard Murray, Cara‐Lena Nies, Cathal Larrigy, Martina Piletti, Jahidul Islam, Daniela Iacopino, Eileen Hurley, Michael Nolan, Aidan J. Quinn   +9 more
wiley   +1 more source

Experimental Study on the Modified P-V-T Model to Improve Shrinkage Prediction for Injection-Molded Semi-Crystalline Polymer. [PDF]

Polymers (Basel)
Chen SC, Liang YX, Ding CJ, Ting YH.
europepmc   +1 more source

Ultra‐Thin Soft Pneumatic Actuation for Minimally Invasive Neural Interfacing

Advanced Materials Technologies, EarlyView.
Parylene C is a common polymer in bioelectronics, favored for its biological and chemical inertness. However, this makes bonding layers of Parylene C together very challenging. Here it is a laser to selectively weld layers of Parylene C to create high‐pressure fluidic actuation devices.
Lawrence Coles, Joe G. Troughton, Alejandro Carnicer‐Lombarte, George G. Malliaras, Christopher M. Proctor   +4 more
wiley   +1 more source

Correlation between carbon percentage and nanocomposite performance in commodity and engineering thermoplastics (ABS, HIPS, PP, and PC). [PDF]

Sci Rep
Essam MA, Nassar A, Nassar E, Younis M.
europepmc   +1 more source