Results 231 to 240 of about 1,157,325 (345)

Powder Metallurgy Preparation of Metastable β Ti–Cr–Ge Alloys for Medical Applications

Advanced Engineering Materials, EarlyView.
This study develops metastable β Ti–Cr–Ge alloys using powder metallurgy for biomedical implants. The Ti–10Cr–2Ge alloy exhibits superior mechanical performance with high yield strength (>1100 MPa), low Young's modulus (<85 GPa), and excellent strain hardening behavior.
Teddy Sjafrizal, Damon Kent, Ali Dehghan‐Manshadi, Matthew S. Dargusch   +3 more
wiley   +1 more source

The Progress of Cognitive Dysfunction Impairment Caused by Temporal Lobe Epilepsy. [PDF]

J Mol Neurosci
Wang Q, Geng Y, Li X, Hao Y, Huang S.
europepmc   +1 more source

don't accept a low plasticity SBR that's physically unfit... [PDF]

, 1964

openalex   +1 more source

Titanium‐S23: A New Alloy with Ultra‐High Tensile Toughness Directly from the Solid‐State Processing of Recycled Ti–6Al–4V and Ti–5Al–5Mo–5V–3Cr Powders using Field Assisted Sintering Technology

Advanced Engineering Materials, EarlyView.
This study explores combining two existing aerospace titanium alloy powders, processing them via field‐assisted sintering technology and the subsequent discovery of a novel alloy composition, termed S23, with ultra‐high tensile toughness. Fine‐scale alpha precipitates favorably form in the alloy despite the relatively slow cooling, providing an ...
Samuel Lister, Gavin J. Baxter, Martin Jackson   +2 more
wiley   +1 more source

Critical period plasticity is associated with resilience to short unpredictable stress. [PDF]

Front Behav Neurosci
Williams R, Van Den Oord C, Lee EN, Fedde SC, Oscherwitz GL, Ribic A.   +5 more
europepmc   +1 more source

Plasticity Analysis of Discontinuous Chip Formation (Part 2)

, 1967
Eiji USUI, Kazuyuki Kikuchi, Takeaki KITAGAWA   +2 more
openalex   +2 more sources

New Developments in the Field of Production and Application of Multi‐Material Wire Arc Additive Manufacturing Components: A Review

Advanced Engineering Materials, EarlyView.
The utilization of direct energy deposition (DED)‐arc additive manufacturing processes in industrial applications is increasing, and these processes have the potential for multi‐material applications. This work provides a overview of the state of research in DED‐arc made functional graded structures, to establish a link to potential industrial ...
Kai Treutler, Volker Wesling
wiley   +1 more source

Hedgehog topological defects in 3D amorphous solids. [PDF]

Nat Commun
Bera A, Zaccone A, Baggioli M.
europepmc   +1 more source

Mitigation of Cracks in High‐Performance Nickel‐Based Superalloys in Powder Bed Fusion Laser Beam of Metals Using a Metal Matrix Composite Approach

Advanced Engineering Materials, EarlyView.
High‐performance nickel‐based superalloys are often not processible in additive manufacturing (AM) due to hot cracking. The findings in this manuscript propose an efficient method to mitigate cracking and enhance mechanical properties of these alloys by producing a metal matrix composite, contributing to the material and process perspective of the AM ...
Klaus Büßenschütt, Maël Pontoreau, Christian Haase, Johannes‐Henrich Schleifenbaum   +3 more
wiley   +1 more source

Influence of Heat Treatment on Microstructure and Mechanical Properties at Elevated Temperatures of Nonweldable Ni‐Based Alloy Printed by Fused Filament Fabrication

Advanced Engineering Materials, EarlyView.
The fused filament‐fabricated MAR‐M247 alloy without hot isostatic pressing shows the lowest porosity of 4%. Heat treatment at 1220 °C produces coarse precipitates and carbides. Specimens heat‐treated at 1220 °C exhibit higher tensile strength (683 MPa) and elongation (10%) at room temperature.
Haneen Daoud, Ying Zheng, Agata Kulig, Natalja Agarkov, Esma Mese, Wolfgang Hofmann, Peter Würtele, Uwe Glatzel   +7 more
wiley   +1 more source