Results 71 to 80 of about 62,593 (266)
Glimpse into reports on abrasive machining (Group G) during CIRP 2024 General Assembly
Jin'gangshi yu moliao moju gongchengTo promote the international cutting-edge technical exchange in the field of abrasives, the Group G (abrasive processing) papers in the 2024 CIRP Annals – Manufacturing Technology journal have been specially selected for introduction. A total of 9 papers
Jiang GUO, Rongyan SUN, Zili ZHANG
doaj +1 more source
Advanced Engineering Materials, EarlyView.A two‐dimensional multiscale finite element analysis framework was established for the first‐generation MoSiBTiC alloy, and the mechanical and fracture‐related parameters of the constituent phases were calibrated through experiments and simulations. The framework provides a basis for analyzing crack propagation behavior in its complex microstructure ...
Junfeng Du +4 more
wiley +1 more source
Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing
Advanced Engineering Materials, EarlyView.The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai +6 more
wiley +1 more source
Chemical mechanical polishing process parameters of 304 stainless steel
Jin'gangshi yu moliao moju gongcheng, 2016 When chemical-mechanically polishing 304 stainless steel,the effects of polishing pressure,polishing slurry flow rate,polishing speed and polishing time on the material removal rate and surface roughness are studied for better performance,lower cost and ...
LI Qing +5 more
doaj
Advanced Engineering Materials, EarlyView.The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat +5 more
wiley +1 more source
AntibioticsBackground: Monolithic zirconia has attracted considerable interest in dentistry due to its favorable physical and mechanical properties, making it a promising alternative for crown fabrication.
Gabriela de Arruda Ribeiro +7 more
doaj +1 more source
Fatigue Crack Initiation and Growth in Nanocrystalline Ni at Multiple Length‐Scales
Advanced Engineering Materials, EarlyView.Overview of miniaturized in situ SEM fatigue setup and resultant fatigue crack growth data for nanocrystalline Ni. The presented study focuses on the analysis of fatigue crack growth rate (FCGR) in focused ion beam‐notched microcantilevers prepared from nanocrystalline (NC) Ni as a model material.
Igor Moravcik +7 more
wiley +1 more source
Spatially Selective Ultraprecision Polishing and Cleaning by Collective Behavior of Micro Spinbots
Small StructuresUntethered magnetic actuation is an attractive technique for controlling a batch of micrometer‐sized soft robots. Recent advancements have enabled each robot to follow its path independently using a single magnetic device.
Hyeongmin Je +3 more
doaj +1 more source
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, EarlyView.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source