Results 51 to 60 of about 994,592 (281)
Controlled carbonization of an Al‐MOF partially decomposes its linkers, exposing coordinatively unsaturated Al centers within an oxide/carbon composite. The resulting Lewis acid sites, rather than surface area, govern organochlorine capture: the composite removes chemically diverse organochlorines from waste plastic pyrolysis oil, outperforms a ...
Seong Cheon Kim +6 more
wiley +1 more source
Five Schiff bases derived from melamine have been used as efficient additives to reduce the process of photodegradation of poly(vinyl chloride) films. The performance of Schiff bases has been investigated using various techniques.
Gamal A. El-Hiti +7 more
doaj +1 more source
MORPHOLOGICAL AND STRUCTURAL INVESTIGATION OF THE POLY(VINYL CHLORIDE) / GRAPHENE OXIDE COMPOSITES
The morphological and structural properties of the poly(vinyl chloride)/graphene oxide (PVC/GO) composites are reported. By the mixture of the two constituents, the PVC/GO composite membranes with a concentration of the GO sheets varying from 0 wt.% to ...
Luiza STÎNGESCU +14 more
doaj +1 more source
Poly(vinyl chloride) processes and products. [PDF]
Poly(vinyl chloride) resins are produced by four basic processes: suspension, emulsion, bulk and solution polymerization. PVC suspensions resins are usually relatively dust-free and granular with varying degrees of particle porosity. PVC emulsion resins are small particle powders containing very little free monomer.
openaire +3 more sources
An ultrathin nanocomposite MXene‐based multilayer effectively blocks hydrogen permeation by presenting a tortuous, layered structure. When the MXene is layered with reduced graphene oxide modified with a polycation, the resulting nanocomposite retains its hydrogen gas barrier properties at temperatures as high as 400°C (permeability of 7.13 ± 0.09 × 10−
Yang Hyun Auh +6 more
wiley +1 more source
Prediction of Zero Shear Viscosity of Poly (Vinyl Chloride) Plastisols
The rheological behaviour of PVC plastisols composed of a blend of suspension and micro-suspension resins in different proportions was investigated. The present work was mainly focused on the variation of the zero shear viscosity versus the concentration
Lainé Carole, Cassagnau Philippe
doaj +1 more source
A new poly(vinyl chloride) membrane sensor that is highly selective to Cr3+ ions was prepared by using diethyl 2-phthalimidomalonate (DPM) as a suitable neutral carrier.
Hassan Ali Zamani, Sara Sahebnasagh
doaj +1 more source
Polypyrrole Aerogels: Efficient Adsorbents of Cr(VI) Ions from Aqueous Solutions
Three-dimensional and porous polypyrrole (PPy) aerogels were prepared using a facile two-step procedure in which cryogels were synthesized via the cryopolymerization of pyrrole with iron (III) chloride in the presence of supporting water-soluble polymers
Patrycja Bober +6 more
doaj +1 more source
Review of pulmonary effects of poly(vinyl chloride) and vinyl chloride exposure. [PDF]
The contributions of several recent reports to the definition of pulmonary effects of PVC dust inhalation are reviewed. Granulomatous reaction, with inclusion of PVC particles in macrophages and histocytes, and associated interstitial pulmonary fibrosis have been found to lead to exertional dyspnoea, diffuse micronodular chest radiographic opacities ...
openaire +2 more sources
Biodegradable Conductors for Implantable and Wearable Transient Bioelectronics
Biodegradable conductors are essential building blocks for transient bioelectronics, enabling temporary sensing, stimulation, and energy transfer while eliminating the need for device retrieval. This review summarizes biodegradable metals, conducting polymers, ionic conductors, and conductive composites, highlighting degradation mechanisms, material ...
Yicheng Zhu, Yijun Liu, Naoji Matsuhisa
wiley +1 more source

