Results 41 to 50 of about 1,165 (208)
Nonoxide Sol-Gel Synthesis of Terbium-Doped Silicon Nitride Phosphors
, 2009 Exposure of solutions of Tb(N(SiMe3)2)3 with SiCl(NEt2)3 in tetrahydrofuran to dry ammonia results in polymeric xerogels. Heating these gels in ammonia leads to amorphous Tb:SiNx phosphors that exhibit bright green luminescence under UV irradiation.
Hector, Andrew L. +3 more
core +1 more source
Machines, 2022 Pulse laser grinding (PLG), as a cutting tool processing method, can not only achieve edge sharpening with high precision, but it can also produce surface modification.
Xiaoxu Liu +5 more
doaj +1 more source
Advances in Magnesium‐Based Thermoelectrics: A Critical Review
Advanced Materials, EarlyView.Magnesium‐based thermoelectric materials have emerged as promising candidates for low‐to‐mid‐temperature energy conversion due to their abundance, low cost, and competitive performance. This review summarizes recent advances in Mg3X2, MgAgSb, and Mg2X systems, covering transport mechanisms, fabrication strategies, stability challenges, and device ...
Li‐Min Zhang +5 more
wiley +1 more source
Influence of Niobium Addition on Microstructure and Machinability of High Chromium Cast Iron
Materials Research, 2021 High Chromium Cast Iron (HCCI) is mostly utilised in environments under severe abrasion and corrosion wear conditions, and research on this material with added niobium obtained positive results regarding wear resistance.
Anderson Edson da Silva +3 more
doaj +1 more source
Flexoelectricity in Photoconversion: Fundamentals, Materials, and Outlooks
Advanced Science, EarlyView.Mechanical bending of a flexible cantilever induces a strain gradient in the photoactive material. The resulting flexoelectric field couples with photovoltaic and photoconductive effects, modulating charge generation, separation, and collection. A comparative analysis of oxide perovskites, halide perovskites, and two‐dimensional materials is presented,
Xiang Huang, Feng Li, Rongkun Zheng
wiley +1 more source
Research on PCBN Tool Dry Cutting GCr15
Machines, 2018 This paper is based on the theoretical analysis designs of a dry cutting orthogonal test in order to study a phenomenon that the radial force is larger than the main cutting force when a PCBN (polycrystalline cubic boron nitride) tool hard turns GCr15 ...
Qinghua Li +3 more
doaj +1 more source
Microstructures and mechanical properties of PCBN materials
Jin'gangshi yu moliao moju gongcheng, 2022 The PCBN material was prepared by high temperature and high pressure method at 1 500℃ and different holding times with CBN-TiN-Ti-Al2O3 as the initial raw material. The phase compositions, microstructures, mechanical properties and cutting performance of
Bin ZHANG, Hongyi GUO
doaj +1 more source
Application of Polycrystalline Cubic Boron Nitride for Cutting Tools.
THE REVIEW OF HIGH PRESSURE SCIENCE AND TECHNOLOGY, 1994 Polycrystalline cubic boron nitride (pcBN) materials, which are produced by sintering cBN powder and binder material under ultra-high pressure and temperature conditions, have so high hardness, high thermal conductivity and very weak affinity for ferrous metals that pcBN has been used for cutting ferrous metals such as hardened steel, cast iron, powder
openaire +2 more sources
Advanced Intelligent Discovery, EarlyView.We discovered novel materials with giant dielectric constants by combining first‐principles phonon calculations and machine learning. Screening 525 perovskites identified six candidates. RbNbO3 was synthesized under pressure and showed ε ≈ 800–1000. This validates our framework as a powerful tool for high‐performance dielectric materials discovery.
Hiroki Moriwake +9 more
wiley +1 more source
Influence of the preparation processes on the residual stresses in PCD and PcBN tools
European Journal of MaterialsUltra-hard cutting materials such as polycrystalline diamond (PCD) and cubic boron nitride (PcBN) are increasingly being used as cutting tools in machining.
Bernd Breidenstein +2 more
doaj +1 more source