Results 21 to 30 of about 167 (137)
Технічна інженерія, 2022 The use of hardened steels and high-hardness alloys provides the necessary mechanical and operational properties of machine parts and mechanisms, as a result of which the demand for the use of such materials is constantly growing.
A.O. , Yu.O. , S.A., S.An.
doaj +1 more source
Cutting Performance and Wear/Damage Characteristics of PCBN Tool in Hard Milling
Applied Sciences, 2019 In the intermittent machining of hardened steel for the die and mold industry, determining how to reduce the wear of PCBN (Polycrystalline Cubic Boron Nitride) tools and improve their machining efficiency and quality is an important subject.
Haining Gao, Xianli Liu, Zhitao Chen
doaj +1 more source
Jin'gangshi yu moliao moju gongchengPolycrystalline cubic boron nitride composites were prepared under high-temperature and high-pressure conditions. The effects of bonding agent ratio and cBN particle size on the composition, microstructure, microhardness, and abrasive ratios of the PcBN ...
Qin ZOU +5 more
doaj +3 more sources
Hard machining of agricultural machines parts
Research in Agricultural Engineering, 2013 For the renovation and/or improvement of the surface properties of machine elements, hard facing is often used. Hard structures obtained in layers or by heat treatment achieve a hardness of up to 68 hardness (HRC) or even more.
R. Drlička +4 more
doaj +1 more source
Investigation on Effect of Material Hardness in High Speed CNC End Milling Process
The Scientific World Journal, Volume 2015, Issue 1, 2015., 2015 This research paper analyzes the effects of material properties on surface roughness, material removal rate, and tool wear on high speed CNC end milling process with various ferrous and nonferrous materials. The challenge of material specific decision on the process parameters of spindle speed, feed rate, depth of cut, coolant flow rate, cutting tool ...
N. V. Dhandapani +3 more
wiley +1 more source
Advances in Materials Science and Engineering, Volume 2014, Issue 1, 2014., 2014 Mechanical properties and failure behaviors of friction stir spot welded (FSSW) joints of two dissimilar ferrous alloys, cold‐rolled carbon steel (SPCC) and 409L stainless steel (SUS 409L), are investigated under opening‐dominant combined loads. The texture of dissimilar FSSW joints depends on the upper sheet material. The failure contours for the FSSW
Md. Abu Mowazzem Hossain +6 more
wiley +1 more source
Effect of nano-diamond on mechanical properties of polycrystalline cubic boron nitride
Fenmo yejin jishuPolycrystalline cubic boron nitride (PcBN) was sintered at the high temperature of 1500 ℃ under the pressure of 5.5 GPa, using cubic boron nitride (cBN) powders as the raw materials, Al powders and Si powders as the binders, and nano-diamond as the ...
ZHANG Qunfei +4 more
doaj +1 more source
PCBN Performance in High Speed Finishing Turning of Inconel 718
Metals, 2018 Inconel 718 is a Ni superalloy widely used in high responsibility components requiring excellent mechanical properties at high temperature and elevated corrosion resistance.
José Díaz-Álvarez +3 more
doaj +1 more source
Review on cutting performance and wear mechanism of PCBN tools
Jin'gangshi yu moliao moju gongcheng, 2020 Polycrystalline cubic boron nitride (PCBN) tool is another kind of superhard tool after polycrystalline diamond tool. It is known as the green environmental protection tool in the 21st century for its unique advanced cutting methods such as turning ...
CUI Jinmeng +4 more
doaj
Journal of Materials Research and Technology, 2019 The microstructure and mechanical properties of 8-mm-thick friction stir welded SAF 2507 super duplex stainless steel pipe was examined. High-quality welds were successfully produced using polycrystalline cubic boron nitride (PCBN) tool, force control ...
Rafael Arthur Reghine Giorjão +6 more
doaj +1 more source