Results 141 to 150 of about 1,042,760 (299)

Synthesis and antimicrobial applications of α-peptoid polymers. [PDF]

Chem Sci
Xie J, Hu W, Feng X, Liu Z, Zhou M, Liu R.   +5 more
europepmc   +1 more source

Low Temperature-Cationic Polymerization of α-Methylstyrene and the Properties of Polymer Obtained

, 1959
Seizô Okamura, Toshinobu Higashimura, Yukio Imanishi   +2 more
openalex   +2 more sources

Magnetic Study on High Polymers. I. Diamagnetic Anisotropy of Natural Rubber [PDF]

, 1953
A. Isihara, Hazime Kusumoto, Hiroshi Nagano, Keichi Oshima   +3 more
openalex   +1 more source

New Developments in the Field of Production and Application of Multi‐Material Wire Arc Additive Manufacturing Components: A Review

Advanced Engineering Materials, EarlyView.
The utilization of direct energy deposition (DED)‐arc additive manufacturing processes in industrial applications is increasing, and these processes have the potential for multi‐material applications. This work provides a overview of the state of research in DED‐arc made functional graded structures, to establish a link to potential industrial ...
Kai Treutler, Volker Wesling
wiley   +1 more source

Uncovering three-body competition of chain growth, degradation and re-aggregation for polyphenylacetylenes during solution polymerization. [PDF]

RSC Adv
He W, Zhou L, Yang J, Zhu M, Li L.
europepmc   +1 more source

Influence of Heat Treatment on Microstructure and Mechanical Properties at Elevated Temperatures of Nonweldable Ni‐Based Alloy Printed by Fused Filament Fabrication

Advanced Engineering Materials, EarlyView.
The fused filament‐fabricated MAR‐M247 alloy without hot isostatic pressing shows the lowest porosity of 4%. Heat treatment at 1220 °C produces coarse precipitates and carbides. Specimens heat‐treated at 1220 °C exhibit higher tensile strength (683 MPa) and elongation (10%) at room temperature.
Haneen Daoud, Ying Zheng, Agata Kulig, Natalja Agarkov, Esma Mese, Wolfgang Hofmann, Peter Würtele, Uwe Glatzel   +7 more
wiley   +1 more source

Design and Synthesis Optimization of Fluorescent Acrylate-Based and Silicate-Based Materials for Carbonyl Adsorption. [PDF]

Polymers (Basel)
Carballido L, Karbowiak T, Bou-Maroun E.
europepmc   +1 more source

Investigation of Iron‐Aluminide‐Like Phase Composition in Complex Concentrated Fe32Cu12Ni11Ti16Al29 Alloy

Advanced Engineering Materials, EarlyView.
This work reveals the phase composition and quantitative morphology analysis of precipitation‐hardened Fe32Cu12Ni11Ti16Al29 complex‐concentrated alloy. The precipitates are shown to have a high coherency. Morphology transition between sphere, cuboidal, and elongated morphology is observed. Finally, the overaging behavior is captured using microhardness.
Rostyslav Nizinkovskyi, Lukas Hanisch, Georg Hasemann, Puspendu Sahu, Manja Krüger   +4 more
wiley   +1 more source

Comparison of polymerization behaviors, microhardness and compressive strength between bulk-fill resin and dual-cured core resin. [PDF]

BMC Oral Health
Kim HJ, Kwon J, Kim HJ, Kim RH, Kim DS, Jang JH.   +5 more
europepmc   +1 more source

(130)The Heat of Polymerization of Styrol and Methacrylate

, 1946
Sinzi IWAI
openalex   +2 more sources