Results 141 to 150 of about 23,557 (277)
High Voltage, EarlyView.ABSTRACT Low‐voltage cables insulated with silicone rubber were harvested from three locations in the primary containment vessel of a boiling water nuclear power plant (NPP). Subsequently, the cable, which was placed in an ambient environment with a relatively higher temperature and the highest rate, was cut into four shorter ones.
Yoshimichi Ohki +2 more
wiley +1 more source
High Voltage, EarlyView.ABSTRACT Maleic anhydride (MAH) grafting modification is an effective approach to enhance the insulating performance of polyethylene (PE) cable insulations. However, the high polarity of MAH often causes considerable dielectric loss, making it unsuitable for AC systems.
Shixun Hu +12 more
wiley +1 more source
Liver preservation with lidoflazine and the university of wisconsin solution: A dose-finding study [PDF]
, 1993 Jacobsson, J +3 more
core +1 more source
Simulation‐Based Material Design for HVDC Cable Accessories
High Voltage, EarlyView.ABSTRACT The worldwide increasing demand for electricity, coupled with the need for more reliable infrastructures and more interconnected networks, has put forward high voltage direct current (HVDC) technologies for energy transmissions. Questions still arise as regards synthetic insulation for cable systems and accessories, as it remains one of the ...
Thi Thu Nga Vu +2 more
wiley +1 more source
Radiation effects design handbook. Section 3 - Electrical insulating materials and capacitors [PDF]
Steady state radiation effects on electrical insulating materials and capacitors ...
Hamman, D. J., Hanks, C. L.
core +1 more source
Dental Traumatology, Volume 41, Issue 2, Page 213-223, April 2025.ABSTRACT Background/Aim This study aims to evaluate and compare the impact absorption capacities of thermoformed ethylene vinyl acetate (EVA) mouthguards and 3D‐printed polyolefin mouthguards used in sports dentistry applications. The objective is to determine whether 3D‐printed polyolefin mouthguards offer superior impact toughness compared to ...
Leonardo Mohamad Nassani +5 more
wiley +1 more source
Research on a Polyolefin Composite Modifier for High-Temperature and Heavy-Duty Pavement and Performance of Its Modified Asphalt. [PDF]
Polymers (Basel)Ding R +5 more
europepmc +1 more source
Impact of Processing Parameters on the Morphology and Performance of PE/PA6/EVOH Blends
Journal of Applied Polymer Science, Volume 143, Issue 11, March 15, 2026.Precise processing conditions enable the utilization of all components in multilayer films, resulting in improved morphology and mechanical properties. ABSTRACT This study employs a stepwise approach to investigate the influence of processing conditions and blend composition on the morphology and mechanical properties of immiscible polymer blends.
Kateřina Papšíková +4 more
wiley +1 more source
Journal of Applied Polymer Science, Volume 143, Issue 11, March 15, 2026.Pure PP and PP/MoO 3 filaments produced by melt spinning. ABSTRACT Polypropylene (PP) composite fibers containing 0.10, 0.20, and 0.50 wt% molybdenum oxide (MoO 3 ) nanoparticles were produced via melt spinning. In the present study, the effect of this addition on the mechanical, thermal, and chromic properties of the fibers was investigated.
Raphael Borges Magalhães Bergamini +5 more
wiley +1 more source
Journal of Applied Polymer Science, Volume 143, Issue 11, March 15, 2026.Influence of acrylonitrile (ACN) content on the processing behavior and morphological development of PA/NBR thermoplastic vulcanizates. Torque‐time profiles, SEM, and SEM/AFM images show that an intermediate ACN level (38%) promotes improved phase dispersion and morphological uniformity, especially with increased processing time, resulting in the most ...
André Luís dos Santos da Silva +4 more
wiley +1 more source