Results 241 to 250 of about 1,549,325 (349)
HEAT-TREATMENT OF POLYPROPYLENE FIBERS
Sen'i Gakkaishi, 1962 Shunsuke Kuribayashi, Akiyoshi Nakai
openaire +2 more sources
Experimental Study on Polymer–Polymer Interfacial Thermal Resistance
Macromolecular Theory and Simulations, Volume 34, Issue 2, March 2025.Interfacial thermal resistance (ITR) in polymer–polymer interfaces is experimentally measured in this paper by the multi‐layered bulk sample approach. Based on numerical simulation and experimental verification, new techniques of layer‐overlapping samples are developed.
Yinfeng Xia +2 more
wiley +1 more source
Synergistic Adsorption for Parabens by an Amphiphilic Functionalized Polypropylene Fiber with Tunable Surface Microenvironment. [PDF]
ACS Omega, 2020 Ran J +5 more
europepmc +1 more source
Polymer Composites, EarlyView.Comparison of experimental and model‐predicted erosion rates for carbon fibre‐reinforced polymer (CFRP) and glass fibre‐reinforced polymer (GFRP) under low‐velocity (2 m/s) and at varying angles and sand concentrations (0.0, 0.05, 0.4 g/L). The results demonstrate good agreement between experimental data and model predictions across different erosive ...
Ali Al‐Darraji +4 more
wiley +1 more source
Polymer Composites, EarlyView.Study of the influence of hornification treatment and jute and mallow fiber length on the physical, thermal, and mechanical properties of recycled polypropylene (PP) composites. ABSTRACT The growing accumulation of plastic waste has driven its reuse in the development of new composites, with natural fibers emerging as promising reinforcements. However,
Raquel de Sousa Freire +4 more
wiley +1 more source
Solid Particle Erosion and Predictive Modeling of Epoxy Composites Reinforced With Diatom Frustules
Polymer Composites, EarlyView.Schematic representation of the solid particle erosion process and predictive modeling workflow for diatom frustule‐reinforced epoxy composites, illustrating the test setup, erosion response curve, and filler‐matrix interaction. ABSTRACT This study examines the solid particle erosion wear behavior of epoxy composites reinforced with 5–20 wt% calcined ...
Elif Gültürk +4 more
wiley +1 more source
Modeling Fiber Dispersion in a Single‐Screw Extruder for Long Fiber‐Reinforced Thermoplastics
Polymer Composites, EarlyView.Fiber dispersion throughout the screw channel ABSTRACT Understanding the mechanics of fiber attrition during the plasticizing process is important in predicting the strength of long fiber‐reinforced thermoplastics (LFT) composites. Fiber dispersion has been found to impact fiber damage during processing and therefore final fiber length in the final ...
Hector Sebastian Perez +4 more
wiley +1 more source
Polymer Composites, EarlyView.Enhanced impact strength in PLLA‐based composites via ε‐caprolactone incorporation in the matrix. ABSTRACT Inherent brittleness and limited toughness of polylactide (PLA) restrict its use in high‐performance applications. To overcome these limitations, poly(L‐lactide) (PLLA) is often blended with more ductile thermoplastics or chemically modified ...
Bernard Miranda Campos +4 more
wiley +1 more source
Polymer Composites, EarlyView.Fused Filament Fabrication and Recycling of Bio‐Based Polyamide 11 Reinforced With Recycled Short Carbon Fibers. Sample preparation, mechanical properties improvement after rCF addition and properties retainment after recycling. ABSTRACT This research investigates the fused filament fabrication (FFF) and recycling of bio‐based polyamide 11 (PA11 ...
Mirko Coser +2 more
wiley +1 more source
The Use of Geofiber and Synthetic Fluid for Stabilizing Marginal Soils [PDF]
, 2007 Connor, Billy +3 more
core